Differences between revisions 25 and 26
Revision 25 as of 09.03.2012 20:12
Size: 20760
Editor: LotharF
Comment:
Revision 26 as of 09.03.2012 20:17
Size: 20761
Editor: LotharF
Comment:
Deletions are marked like this. Additions are marked like this.
Line 249: Line 249:
== Example 2 - Camera set to continuous shootings ==

In this example the camera is set to '''Continuous Shooting''' and takes images as long as the remote is pressed.<<BR>>
== Example 2 - Camera set to Continuous Shootings ==

In this example the camera is set to '''Continuous Shooting''' and takes images as long as the trigger is pressed.<<BR>>

Connect Camera

Prolog

With the MikroKopter you can also carry a camera. Depending on the size of the camrea you can use an appropriate camera mount device.
If you want to trigger the camera from a distance you need to have here an additional module. That can be in example the ShutterCable or the Extension-PCB.

Here now the links for the needed parts:

Connection and Control of the Camera Mount

An attached camera mount through the Kopter you can control over the FlightCtrl.
The camera mount will be maintained over servos in Nick- and Rolldirection (depending on the camera mount).
If you want to adjust the tilt of the camera mount further from the ground by the transmitter it is also possible.
Here you need to assign a free channel on your trasmitter to a potentiometer. That potentiometer will be set over the KopterTool to control the camera mount.

Connection of the camera mount to the FlightCtrl

After the camera mount has been assembled to the Kopter you can connect the servos to the FlightCtrl.
You need to make sure that the connector are connected correctly and in the right way:
(GND= Brown, +5V= Red, Signal= Orange)

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97108&g2_serialNumber=1

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=105542&g2_serialNumber=1

To enlarge click on the image



Connected in that way and after the calibration of the Gyros the camera mount will be hold in balance automatically over the FlightCtrl.

Tilt control of the camera mount over the transmitter

If you want to set also the tilt of the camera mount over the transmitter you can do it over a potentiometer at your transmitter.
HHere you can use every free channel at your transmitter.

In the following example channel 7 should be assigned to this function:

Step 1 - Assign Potentiometer at your transmitter

First at all you need to assign the channel to a potentiometer at your transmitter. A describtion of the assignment you will find in the instruction manual of the transmitter.

Assign channel 7 to a potentiometer at the transmitter:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103272&g2_serialNumber=2
(Example image)

Step 2 - Check function in the KopterTool

You can check in the KopterTool under "Settings" and under the tab "Channels" the function of the potentiometer.
The further you turn the Potentiometer the further goes the peak:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103715&g2_serialNumber=1

On the left side you can see that channel 7 is assigned to the function "POTI3". This "POTI3" will be used for later assignments:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103718&g2_serialNumber=1

Step 3 - Assign Switch Output

So that the camera mount reacts to that channel you need to assign channel 7 to the Nick-Output of the camera mount (POTI3):

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103720&g2_serialNumber=1

After saving that setting you are able now to tilt the camera mount additional and manually over the potentiometer at your transmitter.

If the camera mount is now moving into the wrong direction while moving the Kopter you should set the hook at "invert direction".

TIPP
So that the camera mount is straight under the Kopter after the calibration of the gyros you can adjust the value "Servo control" for Roll manually.
Alternatively you can also use a potentiometer at your transmitter. Here you need to assign an additional free channel to a second potentiometer at the transmitter.
That channel (POTI) will be entered under Roll.

INFO

If you want to control the camera mount over a second transmitter you can do it i.e. over the function TrainerMode (teacher/student).
A describtion with examples you can find here: Trainer Mode

Examples for connections - Trigger camera

The additional PCB (ShutterCable or Extension-PCB) will be connected between the FlightCtrl and the camera.
On the FlightCtrl there are two switch outputs available. For the camera you use the input of the remote controlchinch.
With the ShutterCable is already a 3.5mm jack included which can be used with the most of the cameras.

Tipp
If you use a camera with an other jack you can solder also a suitable connection cable to the ShutterCable or to the Extension-PCB.

The connection could look in that way:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71747
(Example view with the Shuttercable)

Connection example ShutterCable

The ShutterCable can be connected to output 1 or output 2 of the FlightCtrl (SV2):

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97165&g2_serialNumber=1 http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97128&g2_serialNumber=3
(To enlarge click on the image)

Connection example Extension-PCB

The Extension-PCB will be also connected directly to the switch outputs (SV2) of the FlightCtrl. Over the Extension-PCB you can use both switch outputs to the same time.
Here you have the opportunity i.e. to use one output to trigger the camera and the other output to switch the lighting.
Here now an example for the connection:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97123&g2_serialNumber=2
(To enlarge please click on the image)

Trigger camera over a button

So that you can trigger the camera over one of the examples described above you need to set an appropriate channel.
Here you can use each free channel on your transmitter.

In the following example channel 12 should be assigned to that function:

Step 1 - Assign button at the transmitter

First at all you need to assign a button at the transmitter for that channel. A describtion for assigning channels you will find in the instruction manual of the transmitter.

Assign button at the transmitter to channel 12:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103284&g2_serialNumber=2
(Example image)

Step 2 - Check function in the KopterTool

In the KopterTool you can check under "Settings" and under the tab "Channels" the function of the button.
If you do not push the button the appropriate bar (here channel 12) is down below. If you push the button the bar is up:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103676&g2_serialNumber=1

On the left side you can see that channel 12 is assigned to the function "POTI8". This "POTI8" will be used for later assignments:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103634&g2_serialNumber=1

Step 3 - Assign switch output

So that the switch output switches while pushing the button and triggers the camera where the Shuttercable (or the Extension-PCB) is connected "POTI8" (channel 12) will be assigned to that output.
The set up will be done in the "Settings" under the tab "Outputs".

Under "Bitmask" you need to activate only the first casket and the others will be still deactivated. Here the switch output "OFF" is only with a pushed button "ON".
In addition the low-voltage warning for that output will bhe deactivated.
If you leave the low-voltage warning for that output active the output from the battery warning would be continuously activated and triggers the camera unintentionally.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103630&g2_serialNumber=2

Trigger camera continuously

If you want to trigger the camera automatically and continuously during a flight you can do that pretty easy.
To that output (in this example output 1) which triggers the camrea with the ShutterCable or Extension-PCB a fixed time value will be assigned.
In addition you need to set the desired switch sequence over the casket under the tab "Bitmask".

Example 1 - Camera set to single image recording

In this example the camera is set to Single image recording and should take a photo in specific time intervals.
After starting the motors the switch output should be closed every 2 seconds to trigger the camera.

For that you need to set a s follows:

  • Output1 Timing: 100
  • Output1 Bitmask: ON, OFF, ON, OFF,.....
  • "only active after starting the motors" = Activated
  • Green casket behind the Bitmask = OFF


http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103678&g2_serialNumber=1

Throughout the number 100 each casket has a switch period of 1 second (100x10ms = 1sec.).
Is a casket under "Bitmask" "ON" the output will be switched on for the entered time. Is a casket "OFF" the output will be off for that time.
If you checkmark under "only active after starting the motors" you can determine with the appearing green casket behind "Bitmask" wether the function should be done with a running or a not running motor.
Here we leave the casket off so that the function os active with a running motor.

You can enter also different time values under "Timing" and switch the caskets under "Bitmask" ON/OFF in any order.

Here some examples with different times:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103798&g2_serialNumber=1

Bitmask =

ON

OFF

ON

OFF

ON

OFF

ON

OFF

Timing = 50

0,5sek
on

0,5sek
off

0,5sek
on

0,5sek
off

0,5sek
on

0,5sek
off

0,5sek
on

0,5sek
off

Timing = 100

1sek
on

1sek
off

1sek
on

1sek
off

1sek
on

1sek
off

1sek
on

1sek
off

Timing = 200

2sek
on

2sek
off

2sek
on

2sek
off

2sek
on

2sek
off

2sek
on

2sek
off

Out1 is:

ON ->

OFF ->

ON ->

OFF ->

ON ->

OFF ->

ON ->

OFF

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103853&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103850&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103847&g2_serialNumber=2





Example 2 - Camera set to Continuous Shootings

In this example the camera is set to Continuous Shooting and takes images as long as the trigger is pressed.
Here it is necessary that the output is continuously switched on during the complete flight time. That should be active after starting the motors.

For that we need to set as follows:

  • Output1 Timing: 100 (other numbers are also possible)
  • Output1 Bitmask: All caskets ON
  • "only active after starting the motors" = Activated
  • Green casket behind the Bitmask = OFF


http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103681&g2_serialNumber=2

In this case it doesn't matter what number is entered under "Timing". For that reason that all caskets are on this "Funktion" will be done continuously and also the output is continuously switched on.
So that "only active after starting the motors" is activated the switching operation will be started while starting the motors and been stopped while switching the motors off.

Example 3 - Camera set to Continuous Shooting + Switch at the transmitter

In this example the camera is set to Continuous Shooting and takes images as long as the remote is pressed.
But now the "Continuous Shooting" should be started and stopped over a switch at your transmitter.

It is pretty much similar to that what is already described under "Trigger camera over a button".
For that example we also want to use channel 12 again but with a small difference. A switch instead of a button is used:

Step 1 - Assign switch at the transmitter

First at all you need to assign a switch for that channel at the transmitter. A describtion for assigning channels you will find in the instruction manual of the transmitter.

Assign switch to channel 12 at the transmitter:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103267&g2_serialNumber=2
(Example image)

Step 2 - Check function in the KopterTool

In the KopterTool you can check under "Settings" and under the tab "Channels" the function of the button.
If you do not switch the switch the appropriate bar (here channel 12) is down below. If you switch the switch the bar is up:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103676&g2_serialNumber=1

On the left side you can see that channel 12 is assigned to the function "POTI8". This "POTI8" will be used for later assignments:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103634&g2_serialNumber=1

Schritt 3 - Assign switch output

So that the switch output switches while switching the switch and triggers the camera where the Shuttercable (or the Extension-PCB) is connected "POTI8" (channel 12) will be assigned to that output.
The set up will be done in the "Settings" under the tab "Outputs".

Under "Bitmaske" you need to activate the first casket and deactivate the others. Is the switch at your transmitter "OFF" the switchg output is also off. Is the switch "ON" the switch output is also on.
In addition the low-voltage warning for the output will be deactivated.
If you leave the low-voltage warning for that output active the output from the battery warning would be continuously activated and triggers the camera unintentionally.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103692&g2_serialNumber=1

Trigger automatically over the WayPoint-Event

Alternatively to trigger over a button/switch at your transmitter you have the opportunity to trigger the camrea over the WayPoint-Event (WP-Event).
The WP-Event will be used for the WayPoint-Flight. Here you can trigger the camera individually and automatically for each WayPoint.

To use this function you should set everything like under "Trigger camera over a button" described.
So that the switch output reacts to the WP-Event you must assign under "Channels" the appropriate "POTI" to that WP-Event:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=103727&g2_serialNumber=1
(Example how to use POTI8)


A describtion of the WayPoint-Eventyou can find here: WaypointEvent

Align Camera

The camera can be adjusted either way manually via a potentiometer (see "Tilt control of the camera mount over the transmitter")
or automatically during the WayPoint-Flight.

For the automatic tilt of the camera mount you can assign degree numbers for the tilt and for each WayPoint (see MikroKopterTool-OSD#Wegpunkte_-_Vorgaben).
The 0°-Position of the camera you can determine by yourself. The set up will be done before starting the Kopter through the view direction of the camera before the start.

Before starting the camera should be aligned straight.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=104371&g2_serialNumber=2

If the camera should tilt by 90° downwards for this WayPoint-Flight those 90° will be counted to the 0°-Offset:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=104373&g2_serialNumber=2

If you let the camera point a little bit upwards before the start is that direction the 0°-Offset:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=104374&g2_serialNumber=2

If the camera points a little bit downwards before the start is that direction the 0°-Offset.