Unterschiede zwischen den Revisionen 6 und 7
⇤ ← Revision 6 vom 24.10.2011 12:23 →
Größe: 506
Autor: LotharF
Kommentar:
← Revision 7 vom 17.12.2011 19:29 → ⇥
Größe: 460
Autor: LotharF
Kommentar:
Gelöschter Text ist auf diese Art markiert. Hinzugefügter Text ist auf diese Art markiert.
Zeile 1: Zeile 1:
||<tablewidth="520px" tablestyle="text-align: center;"bgcolor="#ffffa0"> {{http://mikrokopter.de/images/deu.gif}} Seite in [[MK-Parameter/Looping|Deutsch]] ||<bgcolor="#ffffa0"> {{http://mikrokopter.de/images/fra.gif}} Page en [[fr/MK-Parameter/Looping|français]] || {{{#!wiki MK_Nav
||<class="MK_Nav_Header" width= "100%">Looping||
||<class="MK_TBody":>'''[[en/MK-Parameter|Back to mainview]]'''||
}}}
Zeile 3: Zeile 6:
||<tablewidth="520px" tablestyle="TEXT-ALIGN: center"bgcolor="#FACC2E"> [[en/MK-Parameter|Back to mainview]]||
{{{#!wiki MK_select1

 * {{http://mikrokopter.de/images/deu.gif}} [[MK-Parameter/Looping|deutsch]]
 * {{http://mikrokopter.de/images/fra.gif}} [[fr/MK-Parameter/Looping|français]]

}}}

Looping

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=91554&g2_serialNumber=1

In the default settings it is not possible to fly a loop with the copter. Is the stick from the transmitter all the way down
the copter is limited from a certain angle point. Only with the activation of one of the directional arrows further tilts and loopings are possible in the selected direction.
In this menu field it can be selected what you want to perform whether loops forward, backward, left or right.
After activating one of the directional arrows only at that point the settings appear.

/!\ Attention: The Kopter can crash when flying loopings! This function is used at your own risk and should be only used by users with flying experience!!

Choosing the functions

  • Arrows

    • The looping is allowed in the desired direction. The arrow points here to the corresponding stick position.

  • Gas Limit

    • At this value the gas is limited during the loop

  • Reaction Point / Response threshold (Ansprechschwelle)

    • From this value it is calculated from the stick position control and changes into a rotation rate control to complete the loop.

    • Hysteresis (Hysterese)

      • Stick-Hysteresis for the reaction point. Normally always lower as the reaction point.

  • TurnOver Nick (Umkehrpunkt Nick)

    • 100 means 100% of a 360° rotation. Also entspricht 1 einem Winkel von 3,6°
      Wenn nach dem Looping der MK zu weit dreht, muss der Wert verringert werden.
      Dreht er nicht weit genug, muss der Wert vergrößert werden.

  • TurnOver Roll

    • 100 bedeutet 100% einer 360° Drehung. So the value of 1 is equal to an angel of 3,6°.
      If after a looping the MK turns to far the value must be reduced.
      If the Kopter does not turn far enough the value must be increased.

/!\ Important

  • The reaction point - hysteresis should be around 20-50. Otherwise the MikroKopter can try during leaving the looping function to go into an angled position
    which is given by the stick. This may leads to very brisk settings so that the Kopter will "jump" and it will miss some
    of the degrees of angular movement what causes the situation that the Kopter will be very oblique.


{i} If the Configuration menu Heading Hold (Nick / Roll) is selected it can be flown loopings without activation of the looping arrows!

  • More information about flying with Heading Hold can be read here: HeadingHold