Unterschiede zwischen den Revisionen 11 und 13 (über 2 Versionen hinweg)
Revision 11 vom 11.04.2012 13:57
Größe: 8140
Autor: LotharF
Kommentar:
Revision 13 vom 22.01.2014 12:54
Größe: 8307
Autor: HolgerB
Kommentar:
Gelöschter Text ist auf diese Art markiert. Hinzugefügter Text ist auf diese Art markiert.
Zeile 7: Zeile 7:
 * {{http://mikrokopter.de/images/deu.gif}} [[SoftwareUpdate|deutsch]]  * {{http://mikrokopter.de/images/deu.gif}} [[ElektronikVerkabelung|deutsch]]
Zeile 63: Zeile 63:
 * [[en/Mini8|Mini8 for BL V3]]
Zeile 120: Zeile 121:

Old PCBs:
Zeile 122: Zeile 126:
New Electronic with [[en/Mini8|Mini8 Distribution]]

{{https://www.mikrocontroller.com/images/Mini8_3.jpg}}

Electronic Connections



Electronic Connections

Overview

Here are the motor (and ESC) numbers, positions, and directions of rotation as seen from behind and above the MK:

Motor

Position

Turns

#1

front

right (clockwise)

#2

rear

right (clockwise)

#3

right

left (counterclockwise)

#4

left

left (counterclockwise)

Tip: ESC/motor #3 is located at 3 o'clock

http://mikrocontroller.cco-ev.de/images/kopter/verdrahtung1.gif

(Klick for higher resolution image)

Connection of receiver, speed controlers (ESC) and batteries (LiPo)

ElektronikVerkabelung/FlightCtrlKabel1k-txt2.jpg

The receiver is connected with a three lead servo wire: +5V, GND and PPM (red, brown/black, orange/yellow).


The LiPo is connected over 2 wires (+ = red, - = brown/black). For lower power applications the BLCtrl power connections are also connected over 2 wires. For higher powered MKs it is safer to create a wiring harnes to connect the ESCs directly to the batteries, and connect the FC through an additional branch to the same harnas. Note that higher power applications may need more powerfull ESCs. For the Holger ESCs the normal wire thickness noted below should suffice).


The I²C-Bus as control bus for the brushless controlers is connected over two or three wires. In the image a two wire connection is shown (SDA = red, SCL = orange). Alternatively you can use 3 wire servo leads and add a GND connection.


cable-Type

min. cable Size

LiPo -> Power-Distribution

1mm² (1.5 or 2 mm² for higher powered applications)

Power-Distribution -> FlightCtrl

0,75mm² (can be 0.3-4 mm² if the batteries are directly banched off of the batteries for higher powered applications)

Power-Distribution -> BL-Ctrl

0,75mm² (1 or 1.5 mm² for higher powered applications)

BL-Ctrl -> Engines

0,5mm² (0.75 to 1 mm² for high power systems)

The I²C connection pads are very close to a mounting hole in the flight controler. Either use plastic or nylon bolts to avoid short-circuits, or connect only 2 wires and branch the different ESCs off at a later point.


/!\ Note: Each of the pairs of pads provides the same signal pair (XD# = SDA, XC# = SCL) These are all connections to the same I²C Bus

Using power distribution boards

Distribution boards make the wiring much simpler

http://gallery.mikrokopter.de/main.php/v/tech/QuadroVerteil_BL.jpg.html

See also:

Connecting powerlines to the flight controler

http://gallery.mikrokopter.de/main.php/v/tech/CIMG8353_Versorgungskabel.JPG.html

The FlightCtrl has two sets of pads for +12V und GND (Minus). In this image red = Plus and black = Minus. In this lower power application the Lipo is directly connected and the ESCs are powered off of the FC. It is also possible, and advised for higher power applications, to power the ESCs directly off of the LiPos before the FC and switch by creating a wiring harnas or power distribution PCB. In that case some thinner wire can be used to connect the FC to the power harnas.


Make sure you connect the LiPo power before the FC on/off switch. If the ESCs are fed off of the 11-12V FC power-supply, they are connected after the switch. This does result in a different behaviour:

  • ESCs fed off of the FC: If the battery is connected but the switch is off, nothing gets powered. If the switch is turned on both the FC and ESCs are powered up.
  • ESCs fed off of the LiPo directly, and FC through a sidebranch: If the battery is connected, the ESCs immediately power up. The FC only powers up after the switch is set to on. Note that normally the ESCs should only beep (actually they cause a hum in the motor windings which is heard as a beep), not turn the propellors. However, in higher power applications make sure you keep away from the propellers when the ESCs are powered up. Safety first.

using the mini power distribution

With this small PCB it is very easy to realize the distribution. The Cables don't have to soldered directly to the FlightControl

http://gallery.mikrokopter.de/main.php/v/tech/MiniVerteiler_connect3.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/MiniVerteiler_connect2.jpg.html

Note in this case: If the FC is connected via the molex-cable, the switch on the FC can't be used. The FC is powered up when the supply is connected to the MiniPowerDistribution

See also: MiniPowerDistribution

Connecting the brushless controlers (ESC)

ElektronikVerkabelung/BLCtrlKabel-txt.jpg

The three wires in the bottom of the image (blue, red, black) go to the brushless motor. The thicker black (GND) and red (11-12V) wires at the top are the power lines to the ESC. They are connected to the battery either through the FC or directly through a wire harnas or power distribution PCB. The red and yellow wire at the right are the I²C connections (red = SDA, yellow = SCL in this image, note that you can also use 3 wire servo leads and connect GND as third wire).

BL-Ctrl

FlightCtrl

J6

XC1, XC2, XC3, XC4

J7

XD1, XD2, XD3, XD4

The sequence of connecting the brushless controlers to the 4 I²C Pads is irrelevant as this is a simple two wire bus. In fact you can also connect all ESCs to a single pair of pads using a wiring harnas or PCB of your own design.


/!\ WARNING: Protect the ESCs from humidity to avoid destroying the Mosfets. Make sure to use heatshrink or Plasticspray to protect the ESCs. However don't fully enclose the ESCs as the Mosfets can get warm, may need to be cooled.

Connecting the motors

Motor 1 (front) and 2 (rear) turn right (clockwise), 3 (right) and 4 (left) turn left (counterclockwise).


The direction of turning is determined by the three wire connection to the ESC. IF a motor turns in the wrong direction just switch two wires.

Connecting other peripherals

Receiver, Servos and others can be connected to the FlightControl. Please see this for the details: FlightCtrl_ME_2_1

Note that on some systems, the channel numbering is different. The MKTool allows you to assign the correct control function to the correct control. The camera tilt control from your transmitter/receiver should be assigned to J7 / camera tilt.

Example of a fully wired up flight controler and brushless controler

Old PCBs:

http://mikrocontroller.cco-ev.de/images/kopter/Elektonik1k.jpg

New Electronic with Mini8 Distribution

https://www.mikrocontroller.com/images/Mini8_3.jpg

Tips

Soldering a Power Distribution ( german Text but u can see what its all about in the Pictures):



    • /!\ ToDo: Would probably be a good idea to show some different wire harnasses, and also include some examples of connectors and their pros and cons.