This page as an PDF-Document? Click on that Symbol and wait a little moment... --->

MikroKopter - QuadroKopter XL

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108317&g2_serialNumber=4

See also: assembly Overview

Info

Please read this manual carefully! This can avoid misunderstandings !
Technical knowledge is recommanded! Wrong soldering can cause damage!

/!\ For the first test you should use a regulated power supply and not the Lipo (battery) !
Wrong soldering or short circuit can destroy the electronics ! Use a power supply of 12V/500mA.

Rigger

Mounting the Motor

/!\ Before you mount the three motor cables into the riggers, you have to check and mount the Motor.
All motors are tested but please check if there is no short circuit between the motor cables and the motor housing.

The motors are mounted with two screws. to avoid loosing the motors, use a little drop of Threadlocker.

/!\ ATTENTION: The screws should be screwed firmly. However, the screw thread in the motor could be overtorqued if too much power!

{i} The threads on the motor (above/below left/right) have different distances!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Motormontage-mit-Sicherungslack.jpg.html

install the motor-, LED-cables

Also mount the red and one black 0,5mm cable (in suitable length) into the riggers wich obtain a LED-stripe or a buzzer.
Please be carefull while installing the cables.

Insert the cable like you see below.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ The cable of the Motor comes out of the hole on the left side of the rigger! (see picture)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html
Example picture

{i} Tips:

  • Stick or solder wires together before pulling them through the hole.
  • if needed, attatch a string to the wires and pull that through first.

/!\ Attention: If you connect the motorcables, it is difficult to turn the motor!

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propeller Mount

The three screws of the propeller mount should be firmly screwed. In this case use a suitable screwdriver!
Later you can mount the propeller like the picture show.

Example: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html

mounting and connecting the LED-strip

/!\ COMMENT: The color of the LED-strip of the Set can vary. Here we describe it with red and blue LED!
The LED-strips of different colors can look equal. Before assembly, the color can be determined by applying a voltage. Terefore a power supply (12V) or a 9V battery that can be used.

/!\ A LED-strip consists of 6 LED's (it could be, that you have to cut a strip)

On the red rigger at the front you can put the red LED-strip. Then put the blue LED-strip on the black riggers.
Now you can solder the red and black Silicone cable (0.5mm²) in the right polarity ("+" red / "-" black) to the LED-strip .
Finally the LED-strip can be shrinked with the transparent shrink hose.

Example of the lighting

Kopter

Red

Blue

Quadro

rigger 1

rigger 2,3,4

Hexa

rigger 1

rigger 3,5

Okto

rigger 1

rigger 4,6



http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarz_LEDaufkleben1.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarz_LEDaufkleben5.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarz_LEDeinschrumpfen1.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarz_LEDeinschrumpfen5.JPG.html

Flight Ctrl. 2.1 - missing parts

The FlightCtrl is already fitted with all needed components.

http://gallery.mikrokopter.de/main.php/v/tech/FC21-best__ckt1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/FC21-best__ckt-2.jpg.html

{i} The FCV2.1 can be connected to the powerboard via the molex cable.

When using the Molexkabel between FlightCtrl and powerboard, you don't have to solder the I2C bus, the buzzer and the power cable to the FlightCtrl.
Only the power cable for the receiver still has to be soldered to the FlightCtrl.
The buzzer is connected directly to the appropriate solder points of the powerboard (Buzzer / -).
The I2C-bus and the voltage supply are provided from the power distribution via the Molex.
Alternatively, the FC V2.1 can be connected with individual cable to the power distributor. But then you don't have to use the Molexcable.

/!\ When mounting the FlightCtrl, the printed arrow shows to the rigger No.1 (red rigger). The PCB populated side facing up.

layout / wiring FC ME 2.1

Describes how a receiver is connected to the FlightCtrl: FlightCtrl 2.1



/!\ In the XL-Set you have a mounted powerboard. How to mount the powerboard with BL-Ctrl you can read here.

Powerboard

Power Distributor - Top

The completely equipped distribution board from the top.
http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=75102&g2_serialNumber=2

Power Distributor - Bottom

The completely equipped distribution board from the bottom.
http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=75106&g2_serialNumber=2

Supply

Connect the batterie cable

On the large "+" and "-" solder pads connect the cable for the Lipo. With a cable tie the cable can be fixed to the power distributor.

  • Plus = red
  • Minus = black

/!\ do not mix plus and minus here!

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=74652&g2_serialNumber=2

Check for short circuit

The contacts (red arrows) are measured with a multimeter. You may not contact or short circuit with each other or have to plus or minus.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=75145&g2_serialNumber=2

Assembling Centerplate

The two Centerplates are keeping the riggers and the electronics together.

/!\ The printed side of the Centerplate always shows up. The arrow always points forward.
/!\ The red arm is front. The rigger, starting with the red one, clockwise from 1-3-2-4.

Example

http://gallery.mikrokopter.de/main.php/v/tech/Centerplate-Quadro.JPG.html

At the top centerplate the four spacers (M3x8 or M3x10) are assembled first. Later, the power distributor is mounted on this spacers. Insert the four spacers with the thread into the centerplate and secured with a nut.
In the next step, the lower and the upper centerplate (with the spacers), can be mounted with the cover holder. Therefore you need 2x plastic screws (M3x16) / plastic nuts (M3).

http://gallery.mikrokopter.de/main.php/v/tech/Centerplate-Quadro-Montage1.jpg.html

Now you can mount the rigger. These are bolted to a metal screw in the center of the centerplate. A second metal screw is inserted from the bottom and secured with a rubber damper (M3x15). Those objectives are later attached to the FlightCtrl. On the rubber damper is still one each M3 plastic nut or a spacer (M3x10) screws to the FlightCtrl give a little more distance.
Those objectives are later attached to FlightCtrl.

On the outer ring of the centerplate, the left and right arm will be attached with two plastic screws(M3x16) / hex nut (M3).

At the front and rear rigger the FlexLander-XL can be installed with metal screws. If you want e.g. rather the HiLander-26 use, the front and rear arm can attached with plastic screw.

http://gallery.mikrokopter.de/main.php/v/tech/Centerplate-Quadro-Montage2.jpg.html

Wiring of the buzzer cable

assembly with buzzer adapter

The buzzer can also be mounted with the buzzer adapter to the Kopter. But take care that the Buzzer is not mounted too close to the FlightCtrl.
This could disturbe the compass!

http://gallery.mikrokopter.de/main.php/v/tech/ExtencionBNR-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/ExtencionBNR-3.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/BuzzerAdapter.jpg.html

{i} We recommend to mount the Buzzer on a 15mm plastic spacer bolt like on the picture. Do not mount it on the Lipo holder. In case of a crash it could cut the cable to the Buzzer.

How to mount the buzzer adapter: Buzzer Adapter

Assembly Powerboard

The Lipo cable is inserted through the Center Plate. Later you can fix it with a cable tie.
http://gallery.mikrokopter.de/main.php/v/tech/Lipoleitung+2.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Lipocable2.jpg.html

After the power board was screwed to the four spacers, the motor cable can be solder. The result:

{i} The arrow of the powerboard shows to the red rigger!

http://gallery.mikrokopter.de/main.php/v/tech/PB-on-centerplate.jpg.html http://gallery.mikrokopter.de/main.php/v/uploads/Quadro.bmp.html <=Quadro

Info:
Motor connection A = gray, B = blue, C = black cable in clockwise rotation.
Motor connection A = blue, B = gray, C = black cable in anticlockwise direction.
If you use motors with different colored cables are tested, the direction of rotation. To change the direction it is enough to replace two cables.

Buzzer

Now the buzzer can be soldered. (BUZZ = +)
http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=74648&g2_serialNumber=2

Lighting

You can connect the lighting (LED) directly to the outer "+" and "-" pad.
http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=75177&g2_serialNumber=2

Lighting switchable

If you want to switch the lights, the optional ExtensionPCB can be used for this purpose. The connection is described here:: ExtensionPCB

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=73058&g2_serialNumber=2

Lipoholder

The Lipoholder can be mounted on four bolts of the cover holder.
http://gallery.mikrokopter.de/main.php/v/tech/Lipoholder-Quadro.jpg.html

connect the FC

The FlightCtrl2.1 will be connected later with the Molex-cable.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=75173&g2_serialNumber=2

/!\ The printed arrow on the FlightCtrl must point to the on the rigger No.1 (red rigger) !

Mounting FlexLanderXL

The FlexLander XL be mounted with supplied screws on the Center Plate.

http://gallery.mikrokopter.de/main.php/v/tech/Flexlander1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Flexlander2.jpg.html

mount transparent cover

Put the cover over the riggers for marking. You can fix it by a tape. Please notenthat the upperpart of the cover is a square. Put one edge of this square towards rigger Nr.1
http://gallery.mikrokopter.de/main.php/v/tech/Cover1.jpg.html

{i} Example mounting on a quadroKopter. On a HexaKopter OktoKopter the sequence is identical!

Now mark the position of the rigger with a pencil.
http://gallery.mikrokopter.de/main.php/v/tech/Cover2.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Cover3.jpg.html

Now it can be cut with scissors and cut the protruding edge.
http://gallery.mikrokopter.de/main.php/v/tech/Cover4.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Cover5.jpg.html

The transparent cover is then attached and secured with a screw. For this you can drilling with a 2mm drill to the cover and the cover holder.
http://gallery.mikrokopter.de/main.php/v/tech/Cover6.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Cover7.jpg.html

If you use the new version of the cover holder you can use the recess on it.
Attention: The recess should be shown up! A matching bolt is located on each motor.
https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=85562&g2_serialNumber=1 https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=85556&g2_serialNumber=2

/!\ The transparent cover should be painted in any color from the inside. This will save the light-sensitive altitude sensor from malfunction. This can happend, if sun's rays strike on the sensor directly.

Cooling hole in the cover

If you use payload > ca. 700g or you fly in high temperatures, a cooling hole (2cm) in the cover might be useful to avoid heat accumulation.

http://gallery.mikrokopter.de/main.php/v/tech/HaubeLoch.jpg.html

First start

Now the Kopter is ready assembled and soldered. The next step is now to check and set the Kopter and the function of the transmitter.
For this we use the KopterTool.

Where you can get the KopterTool and what you have to check/set is explained in simple steps.

Here we go to the easy "steps": Initial startup

safety

A Kopter can be dangerous. Safety comes first, so read carefully: