nouvelle version avec une ergonomie menu améliorée, des paramètres GPS-PID supplémentaires et quelques débogages.
operation:
info. sides and engine test:
Also on the left and on the right the pages through-jump, the last side are the engine test.
Then it changes the 1st side.
attitude parameters and memory:
On the 1st side press downward. One jumps directly on the page 10.
Also on the left and on the right the pages through-jump, the last side are storing.
Then it changes the 1st side
Values change:
Press the arrow once downward on the desired side.
Select also on the left and on the right the value.
Change downward/above then with arrow.
page 1 to 4
See: http://www.mikrokopter.de/ucwiki/JetiBox#Status
On page 3 the maximum total value of current indicated if: The engines any longer do not run and if with fly this Jetiseite is active
page 5
Engine stream, and total value of current if number of engines <=6 engines
It the maximum engine stream indicated if: The engines any longer do not run and if with fly this Jetiseite is active
v or ^ changes the indicator speed
page 6
Engines of control values
v or ^ changes the indicator speed
page 7
I2C error engines 1… 8
v or ^ changes the indicator speed
page 8
Heavy punk announcement
Pitch information positively: Emphasis in front
Roll value positively: Emphasis left
page 9
VSpeed = Variospeed
HG/4 = HoverGas/4 gas = stick gas
page 10
SP1 = Serial potentiometer 1
SP2 = Serial potentiometer 2
SP2 = Serial potentiometer 3
SP2 = Serial potentiometer 4
With the Serial potentiometers 127 is counted, then the range is like a potentiometer to be should
page 11
Hp = Luftdruck_D
Ha = Hoehe_ACC_Wirkung
HP = Hoehe_P
TC = Hoehe_MinGas
page 12
HV = Hoehe_HoverBand
Cycles per second = Hoehe_GPS_Z
Hg = Hoehe_Verstaerkung
HS = Max height
page 13
StP = Stick_P
SGP = Gier_P
StD = Stick_D
DrC = Driftkomp
page 14
GYP = Gyro_P
GYI = Gyro_I
GYD = Gyro_D
May = I_Faktor
page 15
GGP = Gyro_Gier_P
GSt = Gyro_Stability
GGI = Gyro_Gier_I
DSt = DynamicStability
page 16
NGG = NaviGpsGain
NSC = NaviSpeedCompensation
NWC = NaviWindCorrection
NAL = NaviAngleLimitation
page 17
NP = NaviGps p
NI = NaviGps i
Lp = NaviGps D
page 18
LGL = loop gas limit
LHy = loop hysteresis
LTh = LoopThreshold
page 19
FGP = AchsKopplung1 (greed Yaw positive feedback)
FNR = AchsKopplung2 (nod/roll feedback)
CYC = CouplingYawCorrection
UP7 = user parameter 7
(Adjustable Engine SMOOTHING recommended by Arthur P, 0 = off and/or original, 2..5. The engine heading for values are not any longer regulated so hard downward, thus ev. calmer floating)
page 20
NCT = roll servo control: Servo value for swivelling the camera.
NCP = nod Compensation: Influence of the angle of pitch and/or bank angle on the appropriate servo.
RCT = roll servo control: Servo value for swivelling the camera.
RCP = roll Compensation: Influence of the angle of pitch and/or bank angle on the appropriate servo.
page 21
Loop attitude
Loop configuration value 0… 15, decimally
0 = no loop, 15 = loop in all directions possible,
with “<” “>” “^” and “v” is indicated
page 22
Elevator switch or Vario with Beeper switched Hight v Vario withbeep ^
Only 2 attitudes:
Arrow upward: Height by switches
Arrow downward: Height with Vario and Vario bleeper
page 23
Engine test
Arrows left and up or down squeeze together around engine number to adjust
On the top right the appropriate river (*10) becomes indicated
page 24
Settings store (only if engines out)
Arrows on the left and on the right press with one another to store
Arrow upward/down: Into the Setting which can be stored can be selected, Settings beepen with