<> = Introduction = The XBee is a wireless modem that can be used to connect MK Tools running on a laptop to the Flight or Navi Controller on the Mikrokopter. This can be useful for data logging sensor data, making real-time poti adjustments, and for conducting waypoint navigation. <
> = Materials = You'll need two XBee modems. They come in 3 different antenna flavors. Below are listed some modules which operate in the 900Mhz range but there are other frequencies available including 2.4Ghz. * XBee Pro 900 RPSMA http://www.sparkfun.com/commerce/product_info.php?products_id=9099 * XBee Pro 900 wire http://www.sparkfun.com/commerce/product_info.php?products_id=9097 * XBee Pro 900 U.FL http://www.sparkfun.com/commerce/product_info.php?products_id=9098 * U.FL to SMA adapter http://www.sparkfun.com/commerce/product_info.php?products_id=9145 <
> You also need two XBee adapters. One needs to the the USB version, because you just plug that into your computer, and fire up MK-Tool. You can also use the USB version for the MK end, though it's more expensive, and slightly heavier than the "regulated" version which lacks the USB and FTDI stuff. You might have to jumper across a diode on the board as well, since it doesn't play nice with the diode in place. If you're only going to buy two adapters, I'd recommend getting two of the USB versions, since you can use them to test the XBee modems on your computer. If you want more than 2 adapters, then you could get the cheaper ones. <
> * XBee USB Adapter http://www.sparkfun.com/commerce/product_info.php?products_id=8687 * XBee "Regulated" Adapter http://www.sparkfun.com/commerce/product_info.php?products_id=9132[http://www.sparkfun.com/commerce/product_info.php?products_id=9132 <
> Here is another alternate regulator for inside the MK. http://www.droids.it/990_001.html . <
> = Installation = Each XBee modem plugs directly onto the XBee adapter. The Xbee adapter will be used on one end to connect to the computer via USB. On the Mikrokopter side, several wires need to be soldered onto the Xbee adapter so the adapter can be connected to the Flight or Navi controller. Using a 10-pin ribbon cable like the ones included with the Mikrokopter boards will simplify the installation a great deal. If you don't have spare ribbon cable, you can add one of these to your order: http://www.sparkfun.com/commerce/product_info.php?products_id=8535 <
> The connection to the MK : '''MK FC or Navi-board'''.....- ''XBee'' '''Pin 1'''..........................- ''Pin 2 (DOUT)'' '''Pin 2'''..........................- ''5V connection on XBee USB adapter board'' '''Pin 7'''..........................- ''Pin 10 (GND)'' '''Pin 9'''..........................- ''Pin 3 (DIN)'' {{attachment:xbee.jpg}} <
> {{attachment:xbeeboard.jpg}} == Configuration of the Xbee modules == <
> Configure XBee for 57600 baud. <
> Use the XCTU program to do any configuration you need, as well as testing the XBees. http://www.digi.com/support/productdetl.jsp?pid=3352&osvid=57&s=316&tp=5 == Configuration of XBee Pro Series 2 IEEE 802.15.4 ISM 2.4 GHz modules == Setting up Xbee Pro 2 modules for plain point-to-point UART operation is a little more complicated. I got this working with the sparkfun regulator board, one sparkfun USB explorer board and two XBee pro Series 2 modules (all order via http://tinkersoup.de). Works flawless and fast for me. I got the rescuing hints from http://plischka.at/Funk_XBEE.html, here is how it works: Use X-CTU (http://www.digi.com/support/kbase/kbaseresultdetl.jsp?kb=125) and acces via 9600 8,N,1 the first time. Check if you can connect the modules properly first using the test button on the main screen of the tool. You have to configure one module as "COORDINATOR" and the other as "ROUTER" and "hardwire" both modules to get maximum throughput. Go to the Modem Configuration tab and select the appropirate function set. Settings for the coordinator module: * Function Set = "ZNET COORDINATOR 2.5 AT" * PAN ID = select one freely but make sure both modules use the same * DH = SH value the router module * DL = SL value of the router module * BD = 57600 Settings for the router module: * Function Set = "ZNET 2.5 ROUTER/END DEVICE AT" * PAN ID = select one freely but make sure both modules use the same * DH = SH value the coordinator module * DL = SL value of the coordinator module * BD = 57600 Change the settings for both modules accordingly and press the write button. If you like you can update the firmware as well. After a succesful write you get an error message because X-CTU wants to connect to the module with 9600 baud which doesn't work anymore because you changed the value to 57600. Go back to the PC Settings tab and change Baud to 57600 and re-read the settings in the Modem Configuration tab. If you fire up both modules now, one to FC or NC debug and one to your PC via USB the RX/TX DIN/DOUT should start blinking and the RSSI LED should light up. Start MKTool and see if it works. I figured out the I can't access the the USB-connected module via X-CTU if both modules are paired. I have to shut down one of them first. = Content Credit = Rusty (13brv3) http://plischka.at/Funk_XBEE.html KategorieEnglish