Unterschiede zwischen den Revisionen 52 und 118 (über 66 Versionen hinweg)
Revision 52 vom 21.09.2009 13:33
Größe: 19317
Autor: fredericg
Kommentar:
Revision 118 vom 28.04.2010 22:56
Größe: 17129
Autor: anonym
Kommentar: converted to 1.6 markup
Gelöschter Text ist auf diese Art markiert. Hinzugefügter Text ist auf diese Art markiert.
Zeile 1: Zeile 1:
[[TableOfContents(2)]] <<BR>>
<<BR>>
{{attachment:VibTestBanner_small.jpg}}
<<BR>>
<<BR>>
<<BR>>
<<TableOfContents(2)>>
Zeile 4: Zeile 10:
The tool evaluates the vibration generated by the motors which allows balancing motor/prop assemblies and experimenting with different motor-mounts. The test uses the MK build-in sensors, so no extra hardware is required. The tool '''evaluates the vibration generated by the motors''' using the MK build-in sensors, so no additional hardware is needed.

The VibrationTest works with 1.2 and 1.3 FC boards but unfortunately does not work in combination with ME boards without a hardware patch.
<<BR>><<BR>>
The tool can be used to '''balance props, balance motor/prop assemblies''', experimenting with different motor-mounts and so on. As the tool only uses the sensors on the MK FlightControl board, no extra hardware is required.

As the tool can follow the vibrations caused by the prop, it is possible to '''deduce the motor RPM''' at a given speed value. This allows checking if a ESC/motor assembly performs as expected.

For Aerial Photography, it would perhaps be possible to attach a second FC board to a camera to '''visualize the vibrations the camera is exposed to'''. However, this is under investigation if this produces usable results.


<<BR>>

= Why is it important to reduce vibrations? =
The FlightControl sensors pickup the vibrations and this deteriorates performance; the new FC ME comes with vibration dampers in order to reduce the vibrations transferred to the FC.
Zeile 7: Zeile 27:
In addition, the FlightControl sensors pickup the vibrations and this deteriorates performance; the new FC ME comes with vibration dampers in order to reduce the vibrations transferred to the FC.

Propellers can be balanced the traditional way. However it was discovered that also the motors need balancing. One way to accomplish this is let a small unbalance in the prop compensate the motor unbalance, so the orientation of the prop is important (see [http://www.rcgroups.com/forums/showpost.php?p=12832508&postcount=228 this post]). Looking at the vibraions of a running motor allows balancing the prop/motor assembly as a whole.

Propellers can be balanced the traditional way. However it was discovered that also the motors need balancing. One way to accomplish this is let a small unbalance in the prop compensate the motor unbalance, so the orientation of the prop is important (see [[http://www.rcgroups.com/forums/showpost.php?p=12832508&postcount=228|this post]]). Looking at the vibraions of a running motor allows balancing the prop/motor assembly as a whole.

<<BR>>
Zeile 17: Zeile 38:

attachment:test.jpg
<<BR>>
<<Anchor(SampleSignalJpg)>>
{{attachment:test.jpg}}

<<BR>><<BR>>
Zeile 21: Zeile 44:
/!\ ~+'''The version available now (version 0.0) is an alpha version; it was only tested by a limited amount of people. More testers are very welcome!'''+~
[[BR]][[BR]]
The current implementation does not provide a graphical user interface; it is a "command-line" tool. While this approach is a bit less user-friendly, it allows to experiments more freely, which is important at this stage of the project. Later a more fancy user-interface might be added.
[[BR]][[BR]]
Currently the tool was only tested on '''PC/Windows with FC 1.3''' hardware. Theoretically the tool should also run on MAC and Linux.
[[BR]][[BR]]
{i} [http://forum.mikrokopter.de/topic-11446.html MK Forum thread for discussions]
[[BR]]
{i} [[MailTo(frederic AT rc-flight DOT be)]]
/!\ ~+'''Version 1.2 is available'''+~
<<BR>><<BR>>
At the time of writing, the tool was tested in combination with:
 * PC/Windows XP and Vista
 * FC 1.1, FC 1.2 and FC 1.3
 * /!\ '''The Tool does not seem to work well in combination with FC ME without hardware modification.'''
 * /!\ '''Opening the virtual serial port of a Bluetooth dongle might fail.''' I suppose this is the same issue as the most recent MKTool has, will be solved in the next version.
<<BR>>

Theoretically the tool should also run on MAC and Linux.
<<BR>><<BR>>
Features/fixes in the pipeline
 * Tool to help measuring RPM
 * Measurement parameters in different dialog -> more room for results
 * Configurable sampling-rate -> sampling over a longer time is needed is some cases
 * Allow to connect two FC boards for measurement of camera vibrations
 * Integrated backup and restore of flight settings
 * Integrated installing and restore of FC code
<<BR>><<BR>>
{i} [[http://forum.mikrokopter.de/topic-11446.html|MK Forum thread for discussions]]
<<BR>>
{i} <<MailTo(frederic AT rc-flight DOT be)>>


<<BR>><<BR>><<BR>>
<<Anchor(Install)>>
Zeile 32: Zeile 71:
The tool is written in programming language called [http://en.wikipedia.org/wiki/Python_(programming_language) Python].

The most logic and clean way to run the tool is to install support for Python on your PC (if you do not have it already). Python is also available for Linux and MAC; the tool should also run on these platforms, but I have never tried it.
The tool is written in programming language called [[http://en.wikipedia.org/wiki/Python_(programming_language)|Python]].

The most logic way to run the tool is to install support for Python on your PC (if you do not have it already) and the Python libraries the tool depends on.
Python is also available for Linux and MAC; the tool should also run on these platforms, but I have never tried it.
Zeile 40: Zeile 80:
[[Anchor(InstallPython)]]
== Option 1: Install Python ==
<<Anchor(InstallPython)>>
== Option 1: Install Python and required libraries ==
Zeile 44: Zeile 84:
 * [http://www.activestate.com/activepython/ ActivePython for Windows] Press the big "ActivePython Download Now" button.
 * [http://sourceforge.net/projects/pyserial/files/ PySerial (support for serial port access)] Select "pyserial-2.5-rc1.win32.exe" on that page.
Once you have Python support on your PC, unzip [http://www.rc-flight.be/VibrationTest/VibrationTest_0_0.zip VibrationTest_0_0.zip] to a directory on your PC.
 * [[http://www.activestate.com/activepython/|ActivePython for Windows]] Press the big "ActivePython Download Now" button.
 * [[http://sourceforge.net/projects/pyserial/files/|PySerial (support for serial port access)]] Select "pyserial-2.5-rc1.win32.exe" on that page.
 * [[http://www.wxpython.org/download.php|wxPython wxWidgets for Python]] Select the the win32-unicode version for Python 2.6
 * [[http://sourceforge.net/projects/numpy/|NumPy, the fundamental package needed for scientific computing with Python]]
Once you have Python support on your PC, unzip [[http://www.rc-flight.be/VibrationTest/VibrationTest_1_2.zip|VibrationTest_1_2.zip]] to a directory on your PC.
Zeile 49: Zeile 91:
unzip [http://www.rc-flight.be/VibrationTest/VibrationTestExe_0_0.zip VibrationTestExe_0_0.zip] to a directory on your PC
unzip [[http://www.rc-flight.be/VibrationTest/VibrationTestExe_1_2.zip|VibrationTestExe_1_2.zip]] to a directory on your PC


<<BR>><<BR>><<BR>>
Zeile 58: Zeile 101:
attachment:mk1InTest.jpg
{{attachment:mk1InTest.jpg}}

<<BR>><<BR>>

/!\ '''For MKs with bigger motors I have found that it is increasingly important to make sure that the straps do not vibrate too much and stay out of the propwach as much as possible''' Using some soft materials to isolate the straps from the frame and to minimize the strap vibrations improve the quality of the measurements, see picture below.

{{attachment:mk2InTest.jpg}}
<<BR>>
Later in this page it will be explained how the quality of the measurements can be checked.

<<BR>>
<<Anchor(InstallFCSoftware)>>
Zeile 61: Zeile 114:
The VibrationTest tool only works in combination with a special version of the FlightControl software. It must be flashed in the FC board before using the test and you need to reinstall your regular software version afterwards. This just takes a few minutes. Switching the software is done the usual way, using the MKTool. The VibrationTest tool only works in combination with a special version of the FlightControl software. It must be flashed in the FC board before using the test and '''you need to reinstall your regular software version afterwards'''. This just takes a few minutes. Switching the software is done the usual way, using the MKTool.
Zeile 65: Zeile 118:
The LC-Display in the MKTool will look like this:

attachment:LCDisplay.jpg

== The command line ==
The current implementation of the tool does not have a graphical user interface. The simplest way to use the tool is from the command prompt.

On Windows XP open a command shell by selecting Start>Run and typing "cmd".

On Windows Vista, click Start and type "cmd.exe" in the "Start Search" box.

Now, if you have for example unzipped the tool (the Pyhton version or the compiled version) in directory "D:\MK\VibrationToolExe" you should go to that directory by typing:

{{{
D:
cd \MK\VibrationToolExe
}}}
Now, the tool can be started by just typing "VibrationTest.py" if you have installed Python or "VibrationTest" if you use the compiled version. Without any parameters, it tool should display a description of the required parameters.

attachment:cmdLine.jpg

== The command line parameters ==
The tool expects to be started with a few parameters. When the tool is started without or invalid parameters, a brief description of the expected parameters is displayed:

{{{
VibrationTest.py COMPORT MOTORS SPEEDS CHANNELS [-m MINSPEED] [-s NBSAMPLES] [-n NAME] [-d FILENAME] [-v]
 COMPORT Serial port to use. e.g. COM4
 MOTORS Motors to activate during test. Multiple motors can be used at the same time. e.g. 1,2,3,4
 SPEEDS Indicates at what speeds the motors need to be tested.
                   Format 1: e.g. 50,110,140 Tests at speeds 50, 110 and 140
                   Format 2: e.g. 100-200:50 Tests at speeds 100, 150 and 200
 CHANNELS Channels to monitor. e.g. 5,6,7
                   Channel 0 = GyroYaw
                   Channel 1 = GyroRoll
                   Channel 2 = GyroNick
                   Channel 3 = Pressure
                   Channel 4 = Batt
                   Channel 5 = AccTop
                   Channel 6 = AccRoll
                   Channel 7 = AccNick
 -m MINSPEED Minimum speed of the motor(s)
 -s NBSAMPLES Number of samples
 -n NAME Name of the test
 -d FILENAME File to which the measured values will be logged in
 -v Verbose
}}}
4 parameters are mandatory: COMPORT MOTORS SPPEDS and CHANNELS

 * '''COMPORT''': The serial port that is connected to the MK e.g. "COM4"
 * '''MOTORS''': List of motors (comma-separated) that need to run during the test. Typically only one motor will be selected. It is also possible to activate all motors to evaluate the global vibrations before and after calibration for example. e.g. "1" or "1,2,3,4"
 * '''SPEEDS''': List of speeds at which will be tested. The "speed" is the I2C value that will be sent to controller and is a value between 0 and 255. Typically interesting values for vibration-testing vary between 100 and 200. [[BR]]There are 2 formats possible. First there is the simple list of speeds, e.g. "100,150,190,200". The second format specifies the minimum, maximum speed and step, e.g. "100-200:20" will test at 100,120,140 ... 200
 * '''CHANNELS''': List of "channels" that will be monitored. A channel is in fact one of the MK analog sensors. Measuring the pressure or battery does not make much sense in this context, but is it possible. It is my experience that channel 6 and 7 produce best vibration signals, but YMMV.

[[BR]] In addition, these optional parameters can be provided

 * '''-m MINSPEED''': The motor(s) will first be started at "idle" speed before being spooled up to the speed at which the measurement will take place. By default, this speed is 25 but it can be changed with this option. Your motors need to run smootly and start reliably at this speed. In combination with the TP converted ESC for example, the default value of 25 will be too low.
 * '''-s NBSAMPLES''': During a measurement, the FlightControl board will monitor a given channel and store 1000 samples in memory. Afterwards the VibrationTool will read these samples. These samples can be dumped in a file (see the "-d" option) and will be used to find the amplitude of the signal (the difference between the minimum and maximum measured value). [[BR]]It is important to read enough samples to cover a few periods. By default 400 samples are read but with this option, the number of samples can be modified (with a maximum of 1000).
 * '''-n NAME''': An indication of what you are testing. This string will be added to the dumps (see "-d" option) and should not contain spaces e.g. "-n AfterBalancing"
 * '''-d FILENAME''': With this option, all samples will be dumped in a text-file. This file can later be used for further analysis. It can for example be inported in MS Excel or OpenOffice Calc to make graphs of the vibration signal. When the file does not exist yet it will be created, otherwise the new data will be added. All measurements dumped in the same file should have the same number of samples (see the "-s" option) e.g. "-d motor1.txt"
 * '''-v''': With this option, the tool will be much more verbose; it will indicate what it is doing. Also when an error occurs, the tool will provide more technical details (the callstack)

== The output ==
=== The results on the screen ===
Without the "-v" option, only the results of the test is displayed:
{{{
C:\DATA\temp\VibrationTestExe>VibrationTest COM5 1 100,150 6 -n Demo
      Demo Speed=100 U=12.1V Channel=AccRoll Min=497 Max=506 pp= 9 *
      Demo Speed=150 U=11.9V Channel=AccRoll Min=498 Max=508 pp= 10 **
}}}
 * "'''Demo'''" This is the name of the test as we provided with the "-n" option.
 * "'''Speed=100'''" Indicates the motor speed for this measurement
 * "'''U=12.1V'''" The measured battery voltage when the measurement was done
 * "'''Channel=AccRoll'''" The measured channel
 * "'''Min=497'''" Lowest value of all samples
 * "'''Max=506'''" Highest vale of all samples
 * "'''pp=9'''" Difference between Min and Max, this is the actual result
 * "'''**'''" The number of stars gives a quick indication of the pp-value


With the "-v" option more details are provided:
{{{
C:\DATA\temp\VibrationTestExe>VibrationTest COM5 1 100,150 6 -n Demo -v
comPort = COM5
motors = ['1']
minSpeed = 25
speeds = ['100', '150']
channels = ['6']
nbSamples= 400
fileName = None
testName = Demo
Opening comPort...
Version: 0.74
Voltage: 12.1V
Minimum Voltage: 10.5V
Starting motor(s) (speed=25)... OK
Setting speed to 100 ...
Getting data... Demo Speed=100 U=12.1V Channel=AccRoll Min=496 Max=508 pp= 12 **
Setting speed to 150 ...
Getting data... Demo Speed=150 U=11.9V Channel=AccRoll Min=497 Max=508 pp= 11 **
}}}

=== The dumped signal ===
The "-d" option allows to dump the measured signal in a text-file. This is a "comma-separated" text file that can easily be imported in MS Excel or OpenOffice Calc.

attachment:calc.jpg

1000 samples are acoputed in about 90ms (0.09 s), the time between samples is about 0.9 ms (0.00009 s).
Suppose the prop is spinning at 5000 RPM, this means 83 rotations per second. In 0.09s we have captured 7.5 rotations. We we take 400 of the 1000 samples we should see 7.5/1000*400 = 3 rotations of the prop.


== Proposed procedure to balance prop/motor assembly ==
First we need to find what what sensor provides the "best" footage of the vibrations. The largest signal is probably the best. Candidates are Gyro and Acc signals. My experience is that AccNick (channel 7) and especially AccRoll (channel 6) provide the nicest signal, but YMMV. The vibration will typically peak at a certain motor speed. So, first we perform a sweep between speeds 100 to 200 and look at channels 6 and 7 and choose a channel and speed we will concentrate on.

Next I check if the prop can be balanced a bit better. I stick small strips of tape to the prop, close to the center. One strip to the side where the prop-dimension is mentioned I denote as "-1", one strip on the other side, I denote "+1". I test different configurations and check what gives the best results for my chosen channel and speed.

Now that the prop is better balanced, I start to rotate the prop in relation to the motor. As names for the test I use "XsA" where "X" is the number of strips and "A" is the angle; e.g. "+1s60" means 2 strips (opposite to the prop-marking) and rotated by 60 degrees (compared to the starting position). Again I try to find the best position.

Once we have found the best rotation, we can rebalance the prop in the same way as before.

After all this we should have found the best combination. We can perform the swipe again to compare with the starting point.


=== Example 1 ===
This is an example with standard Roxxy 2824-34 motor with EPP 1045 prop.
[[BR]]

Finding what sensor provides best information at what speed:

{{{
VibrationTest.py COM5 3 100-200:20 6,7
      Speed=100 U=11.3V Channel=AccRoll Min=492 Max=505 pp= 13 **
      Speed=100 U=11.3V Channel=AccNick Min=498 Max=507 pp= 9 *
      Speed=120 U=11.3V Channel=AccRoll Min=489 Max=503 pp= 14 **
      Speed=120 U=11.3V Channel=AccNick Min=497 Max=507 pp= 10 **
      Speed=140 U=11.2V Channel=AccRoll Min=469 Max=519 pp= 50 ********** <<=======
      Speed=140 U=11.2V Channel=AccNick Min=495 Max=508 pp= 13 **
      Speed=160 U=11.1V Channel=AccRoll Min=478 Max=517 pp= 39 *******
      Speed=160 U=11.1V Channel=AccNick Min=493 Max=511 pp= 18 ***
      Speed=180 U=10.9V Channel=AccRoll Min=479 Max=511 pp= 32 ******
      Speed=180 U=10.9V Channel=AccNick Min=493 Max=514 pp= 21 ****
      Speed=200 U=10.7V Channel=AccRoll Min=479 Max=515 pp= 36 *******
      Speed=200 U=10.7V Channel=AccNick Min=493 Max=513 pp= 20 ****

VibrationTest.py COM5 3 130-160:10 6
      Speed=130 U=11.1V Channel=AccRoll Min=484 Max=511 pp= 27 *****
      Speed=140 U=11.1V Channel=AccRoll Min=469 Max=524 pp= 55 ***********
      Speed=150 U=11.1V Channel=AccRoll Min=475 Max=520 pp= 45 *********
      Speed=160 U=11.1V Channel=AccRoll Min=479 Max=518 pp= 39 *******
}}}
So, lets concentrate on channel 6 (AccRoll) at speed 140.


Now, the preliminary balancing of the prop:

{{{
VibrationTest.py COM5 3 140 6 -d motor3.txt -n 0s0
  0s0 Speed=140 U=11.0V Channel=AccRoll Min=470 Max=521 pp= 51 **********

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s0
  1s0 Speed=140 U=11.0V Channel=AccRoll Min=482 Max=513 pp= 31 ******

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 2s0
  2s0 Speed=140 U=11.0V Channel=AccRoll Min=475 Max=520 pp= 45 *********
}}}
For now, 1 strip seems best.

Now, lets rotate the prop:

{{{
VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s0
  1s0 Speed=140 U=10.9V Channel=AccRoll Min=481 Max=513 pp= 32 ******

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s60
 1s60 Speed=140 U=10.9V Channel=AccRoll Min=480 Max=512 pp= 32 ******

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s120
1s120 Speed=140 U=10.9V Channel=AccRoll Min=477 Max=514 pp= 37 *******

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s180
1s180 Speed=140 U=10.9V Channel=AccRoll Min=482 Max=509 pp= 27 *****

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s240
1s240 Speed=140 U=10.9V Channel=AccRoll Min=482 Max=510 pp= 28 *****

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s300
1s300 Speed=140 U=10.9V Channel=AccRoll Min=482 Max=514 pp= 32 ******

VibrationTest.py COM5 3 140 6,6,6 -d motor3.txt -n 1s360
1s360 Speed=140 U=10.9V Channel=AccRoll Min=482 Max=515 pp= 33 ******
}}}
Rotating the prop by 180 degrees produces best results, now lets try to balance the prop again:

{{{
VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s180
1s180 Speed=140 U=10.9V Channel=AccRoll Min=483 Max=509 pp= 26 *****

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 0s180
0s180 Speed=140 U=10.9V Channel=AccRoll Min=472 Max=519 pp= 47 *********

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 1s180
1s180 Speed=140 U=10.9V Channel=AccRoll Min=483 Max=510 pp= 27 *****

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 2s180
2s180 Speed=140 U=10.9V Channel=AccRoll Min=489 Max=508 pp= 19 ***

VibrationTest.py COM5 3 140 6 -d motor3.txt -n 3s180
3s180 Speed=140 U=10.9V Channel=AccRoll Min=483 Max=512 pp= 29 *****
}}}
So, 2 stickers is best, let's verify again:

{{{
VibrationTest.py COM5 3 140 6 -d motor3.txt -n 2s180
2s180 Speed=140 U=10.9V Channel=AccRoll Min=488 Max=508 pp= 20 ****

VibrationTest.py COM5 3 140 6 -d motor3.txt -n end
  end Speed=140 U=10.8V Channel=AccRoll Min=487 Max=510 pp= 23 ****
}}}

[[BR]]
Now, we can perform a sweep in order to compare with the starting-point:

{{{
VibrationTest.py COM5 3 100-200:20 6,7
       Speed=100 U=11.1V Channel=AccRoll Min=493 Max=501 pp= 8 *
       Speed=100 U=11.1V Channel=AccNick Min=499 Max=507 pp= 8 *
       Speed=120 U=11.1V Channel=AccRoll Min=489 Max=507 pp= 18 ***
       Speed=120 U=11.1V Channel=AccNick Min=497 Max=508 pp= 11 **
       Speed=140 U=11.0V Channel=AccRoll Min=489 Max=507 pp= 18 ***
       Speed=140 U=11.0V Channel=AccNick Min=498 Max=509 pp= 11 **
       Speed=160 U=10.9V Channel=AccRoll Min=482 Max=508 pp= 26 *****
       Speed=160 U=10.9V Channel=AccNick Min=496 Max=510 pp= 14 **
       Speed=180 U=10.7V Channel=AccRoll Min=489 Max=505 pp= 16 ***
       Speed=180 U=10.7V Channel=AccNick Min=495 Max=508 pp= 13 **
       Speed=200 U=10.6V Channel=AccRoll Min=482 Max=508 pp= 26 *****
       Speed=200 U=10.6V Channel=AccNick Min=491 Max=509 pp= 18 ***
}}}
/!\ '''The FC code for the VibrationTest is based 0.74d but is not fit for flying! Before flying, you will need to reinstall your initial FC code. When the version you use for flying is 0.74d, your settings should be preserved. In combination with other versions, it might not be the case. It is a good idea to backup yout settings to PC (via the MKTool) before installing the VibrationTest FC code. '''

After insatlling the FC code for the VibrationTest, the LC-Display in the MKTool will look like this:

<<Anchor(InstallFCSoftwareJpg)>>
{{attachment:LCDisplay.jpg}}

It is normal that a there is a warning for a missing BL-Ctrl. When you have 4 motors for example, it should complain that it did not find motor 5.


== Starting the VibrationTest tool ==
In the directory where you unzipped the tool, dubbleclick VibrationTestGui.py (in case of the Python version) or VibrationTestGui.exe

== Using the VibrationTest tool ==
<<BR>>
<<Vimeo(6948282)>>
<<BR>><<BR>>
<<Vimeo(7670919)>>
<<BR>>

== Checking the reliability/accuracy of the results ==
Before you start, it is good to check the reliability of the test and setup.

You should alway start with a sweep and look at different sensors. If the vibrations is rather constant over motor-speed, the combination might be well balanced or you might not be measuring what you are hoping to measure. In this case, sticking some tape to the prop should should unbalance it and you should see a difference.
<<BR>>
You can have a look at the recorded signals, the filtered signals and perhaps the spectrum.
The picture below shows an example of (raw) a signal of good quality:

{{attachment:GoodSignal.jpg}}

<<BR>>
The signal below is regular but goes slowly up and down. This is not a big problem as this will be filtered out later; this is still good:

{{attachment:MediumSignal.jpg}}

<<BR>>
The signal in the next picture is of low quality. Propably other components than the motor are vibrating:

{{attachment:BasSignal.jpg}}
 
<<BR>>
<<BR>>
If the signals seem ok, you can repeat the sweep multiple times, using one of the sensors. Each time you should get similar results. Results will never be 100% the same.

Another test you should do, is let the tool measure multiple times at the same speed; for example "10*100,10*200". The measurement at the same speed should report the about the same amount of vibrations.

The figure below shows the result of such test with a "Roxxy 2824-34 / EPP1045 / 3s / Standard ESC" combination. All but the green line are from the Nick sensor. The black line are vibrations measured at speeds 130 and 185. The other lines are sweeps. This does not look too bad.

{{attachment:acuracy1.jpg}}

<<BR>>
(!) When the results are disappointing, one should experiment with the way the MK is attached. One could fix the MK more firmly to the desk or on the contrary allow more movement. One should also and make sure nothing else but the MK can vibrate.

It is also possible that the filter parameters might not be optimal for your setup. In the figure below I have almost disabled the filter and switched to "pp" measurement:

{{attachment:acuracy2.jpg}}

<<BR>>
This is another example of such a test (Turnigy 2836-750 / APC 12x3.8 / 4s / TowerPro ESC):

{{attachment:acuracy3.jpg}}

<<BR>><<BR>>
= Examples =

== Balancing example: Roxxy 2824-34 / EPP1045 / 3s / Standard ESC ==
<<Vimeo(7011506)>>

<<BR>>
== Effect of prop position, Roxxy 2824-34 / EPP1045 3s / Standard ESC ==
The importance of the position of the propeller relative to the motor was first reported by RCGroups member "Old Man Mike", see [[http://www.rcgroups.com/forums/showpost.php?p=12832508&postcount=228|this post]]. My tool also shows this effect. However, I observed that sometimes rotating the prop did not produce significant variations...

I discovered that when I first balance the prop as good as I can using the VibrationTest, rotating the prop produced very little difference.

I come to the conclusion that I need to deliberately unbalance the prop a bit in order to find the "sweet spot". I also observed that when I unbalance the prop by sticking some tape on one side of the prop the vibrations peak while they go trough a minimum when I stick some tape to the other side.
I think this supports the theory that the slightly unbalanced prop can compensate for unbalances in the motor.
<<BR>><<BR>>
{{attachment:StudyRotation.jpg}}
<<BR>><<BR>>
On the X-asis the rotation of the prop in steps of 60 degrees. The red line is with a prop that I balanced before (needs some tape opposite to the prop size-markers). The green line shows vibrations when I attach an additional strip of tape (so unbalancing it). The blue line shows what happens when I attach tape to the other side (where the markers are).

== Balancing example: Turnigy 2836-750 / APC 12x3.8 / 4s / TowerPro ESC ==
<<BR>>
{{attachment:Mk2BalancingExample1.jpg}}
<<BR>>
The red line is the initial balancing. The prop seemed best balanced with no additional tape.<<BR>>
The green line are the measurement while rotating the prop (steps of 45 degrees)<<BR>>
The blue line is the re-balancing, due to the repositioning of the prop the results are better. The first 3 measurements showed that no tape produced the best results. In the last 3 measurements of the blue line, I experimented with smaller strips and this produced the best result.

<<Anchor(MECaps)>>
== Influence of ME ACC capacitors ==
<<BR>>
This example shows why the VibrationTest does not work in combination with FlightControl ME boards.
ME boards have bigger capacitors on the ACC lines and these suppress the signal we are interested in. 1.3 boards have 0.1 uF capacitors while ME has 1 uF capacitors.
<<BR>><<BR>>
To be sure that the issue was due to these capacitors I replaced one of the capacitors and performed some measurements. The first picture below shows the raw signal without capacitor (0uF). The next picture shows the signal with a 0.1uF capacitor, so this corresponds with the capacitor used on 1.3 boards. For the last picture a 1uF capacitor (so the normal value for an ME board) was installed. As you can see the signal is completely suppressed...
<<BR>><<BR>>
[[http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0uF.jpg|{{http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0uF.jpg||width=300}}]]
[[http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0d1uF.jpg|{{http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0d1uF.jpg||width=300}}]]
[[http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-1uF.jpg|{{http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-1uF.jpg||width=300}}]]
<<BR>><<BR>><<BR>>
The pictures below show the spectra of the same signals. As you can see, the 0.1uF cap already filters a lot but leaves the vibration signal visible.
<<BR>> <<BR>>
[[http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0uF-spectrum.jpg|{{http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0uF-spectrum.jpg||width=300}}]]
[[http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0d1uF-spectrum.jpg|{{http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0d1uF-spectrum.jpg||width=300}}]]
[[http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-1uF-spectrum.jpg|{{http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-1uF-spectrum.jpg||width=300}}]]

<<BR>><<BR>>
<<Anchor(Changelog)>>
= Changelog =
||'''Version'''||'''Date'''||'''Changes'''||
||1.2||17/11/2009||- Ability to measure Gyro sigals<<BR>>- Tool to measure RPM||
||1.0||24/10/2009||= 0.9 RC4||
||0.9 RC4||21/10/2009||- FC code: ignore mixing table so that all motors always work<<BR>>||
||0.9 RC3||17/10/2009||- Fixed limitation of 4 motors (not tested)<<BR>>- More parameter checking and clear error reporting<<BR>>- Support to connect to NC<<BR>>- Fixed exception at start of measurement||

<<BR>><<BR>>
= Older versions =

 * 1.0
[[http://www.rc-flight.be/VibrationTest/VibrationTest_1_0.zip|VibrationTest_1_0.zip]]<<BR>>
[[http://www.rc-flight.be/VibrationTest/VibrationTestExe_1_0.zip|VibrationTestExe_1_0.zip]]<<BR>>

<<BR>><<BR>>
Zeile 302: Zeile 243:
 * [http://forum.mikrokopter.de/topic-11446.html MK Forum thread for discussions]
 * [http://svn.mikrokopter.de/mikrowebsvn/listing.php?repname=Projects&path=/VibrationTest/#_VibrationTest_ VibrationTest Project in Subversion]
 * [http://www.rcgroups.com/forums/showthread.php?t=1006721 Old Man Mike "Test Fixture Evaluates Motors/Props/ESCs for Quadcopter Performance"]
 * Mail FredericG: [[MailTo(frederic AT rc-flight DOT be)]]
[[BR]]

## [[AttachList]]

=== VibrationTest related ===
 * [[http://svn.mikrokopter.de/mikrowebsvn/listing.php?repname=Projects&path=/VibrationTest/#_VibrationTest_|VibrationTest Project in Subversion]]
 * [[http://forum.mikrokopter.de/topic-11446.html|MK Forum thread for discussions]]
 * Mail FredericG: <<MailTo(frederic AT rc-flight DOT be)>>

=== Related Threads ===
 * [[http://forum.mikrokopter.de/topic-7794-1.html|Thread: Vibrationsdämpfung der Antriebsmotoren]]
 * [[http://forum.mikrokopter.de/topic-post106888.html|Thread: Tilt servo play => Vibrations]]
 * [[http://www.mk-fr.info/forum/index.php/topic,812.msg12038.html|Thread: Equilibrage des Hélices RC (French)]]
 * [[http://www.vimeo.com/4257366|Video: Is the Optical Image Stabilization of the FX35 causing problems?]]
 * [[http://www.rcgroups.com/forums/showthread.php?t=807347|Thread: Multikopter (mikrokopter, UAVP, x-ufo-3rd, etc) AP pictures]]

=== Related Projects ===
 * [[http://www.rcgroups.com/forums/showthread.php?t=1006721|Old Man Mike "Test Fixture Evaluates Motors/Props/ESCs for Quadcopter Performance"]]

=== Used Libraries and Tools ===
 * [[http://www.python.org/|Python]]
 * [[http://www.wxpython.org/|wxPython]]
 * [[http://wxglade.sourceforge.net/|wxGlade]]
 * [[http://numpy.scipy.org/|NumPy]]
 * [[http://www.py2exe.org/|py2exe]]

=== Technical references ===
 * [[http://en.wikipedia.org/wiki/Sampling_(signal_processing)|Sampling]]
 * [[http://en.wikipedia.org/wiki/Fourier_analysis|Fourier Analysis]]

<<BR>>

<<AttachList>>
Zeile 311: Zeile 275:
 . KategorieTools  . KategorieTools KategorieProjekte KategorieEnglish KategorieAnleitung



VibTestBanner_small.jpg


What is the VibrationTest Tool?

The tool evaluates the vibration generated by the motors using the MK build-in sensors, so no additional hardware is needed.

The VibrationTest works with 1.2 and 1.3 FC boards but unfortunately does not work in combination with ME boards without a hardware patch.

The tool can be used to balance props, balance motor/prop assemblies, experimenting with different motor-mounts and so on. As the tool only uses the sensors on the MK FlightControl board, no extra hardware is required.

As the tool can follow the vibrations caused by the prop, it is possible to deduce the motor RPM at a given speed value. This allows checking if a ESC/motor assembly performs as expected.

For Aerial Photography, it would perhaps be possible to attach a second FC board to a camera to visualize the vibrations the camera is exposed to. However, this is under investigation if this produces usable results.


Why is it important to reduce vibrations?

The FlightControl sensors pickup the vibrations and this deteriorates performance; the new FC ME comes with vibration dampers in order to reduce the vibrations transferred to the FC.

Reducing vibration is very important, especially for Aerial Photography or Video. Vibrations result in blurry footage. Some claim that high frequency vibrations can be picked up by the Optical Image Stabilization lens assembly which is incorporated in almost all recent cameras. The OIS is not designed for these vibrations and makes thing worse, even when you switch the OIS feature off in the camera menu.

Propellers can be balanced the traditional way. However it was discovered that also the motors need balancing. One way to accomplish this is let a small unbalance in the prop compensate the motor unbalance, so the orientation of the prop is important (see this post). Looking at the vibraions of a running motor allows balancing the prop/motor assembly as a whole.


How does it work?

The standard FlightControl program samples all sensors periodically and provides a command to read the latest sample from all sensors. The MKTool uses this command to generate graphs of the analog values. In a first approach the VibrationTest used this standard command to monitor vibrations. The problem is that this mechanism only allows to sample the values 30 times a second. The actual shape of the signals cannot be determined and one can only hope to catch the peak values. In order to get reliable results the values need to be monitored for a long time (a minute for example).

This new approach is based on dedicated FlightControl software providing a new command. The new command instructs the FC to sample one of the sensors as fast as possible and store the info in its internal memory. Afterwards the recorded data can be read to analysis. This allows to grab a reliable signal in a very short time. This approach can capture about 11000 samples a second, 500 times more than the MKTool can.

This is an example of the signal measured by the Roll-ACC sensor:
test.jpg



Current Project status

/!\ Version 1.2 is available

At the time of writing, the tool was tested in combination with:

  • PC/Windows XP and Vista
  • FC 1.1, FC 1.2 and FC 1.3
  • /!\ The Tool does not seem to work well in combination with FC ME without hardware modification.

  • /!\ Opening the virtual serial port of a Bluetooth dongle might fail. I suppose this is the same issue as the most recent MKTool has, will be solved in the next version.


Theoretically the tool should also run on MAC and Linux.

Features/fixes in the pipeline

  • Tool to help measuring RPM
  • Measurement parameters in different dialog -> more room for results

  • Configurable sampling-rate -> sampling over a longer time is needed is some cases

  • Allow to connect two FC boards for measurement of camera vibrations
  • Integrated backup and restore of flight settings
  • Integrated installing and restore of FC code



{i} MK Forum thread for discussions
{i} <frederic AT rc-flight DOT be>




How do I install the tool?

The tool is written in programming language called Python.

The most logic way to run the tool is to install support for Python on your PC (if you do not have it already) and the Python libraries the tool depends on. Python is also available for Linux and MAC; the tool should also run on these platforms, but I have never tried it.

If you do not feel like installing Python, a version that is compiled to a windows executable is provided.

So, you have two options.

Option 1: Install Python and required libraries

For a Windows machine I propose you install:

Once you have Python support on your PC, unzip VibrationTest_1_2.zip to a directory on your PC.

Option 2: Get the compiled version

unzip VibrationTestExe_1_2.zip to a directory on your PC




How do I use the tool?

Prepare your MK

Secure your MK

I use luggage straps to secure my MK to the table while it is still able to vibrate:

mk1InTest.jpg



/!\ For MKs with bigger motors I have found that it is increasingly important to make sure that the straps do not vibrate too much and stay out of the propwach as much as possible Using some soft materials to isolate the straps from the frame and to minimize the strap vibrations improve the quality of the measurements, see picture below.

mk2InTest.jpg
Later in this page it will be explained how the quality of the measurements can be checked.


Installing the FlightControl software

The VibrationTest tool only works in combination with a special version of the FlightControl software. It must be flashed in the FC board before using the test and you need to reinstall your regular software version afterwards. This just takes a few minutes. Switching the software is done the usual way, using the MKTool.

You will find the required hex file in the same directory with the VibrationTest tool.

/!\ The FC code for the VibrationTest is based 0.74d but is not fit for flying! Before flying, you will need to reinstall your initial FC code. When the version you use for flying is 0.74d, your settings should be preserved. In combination with other versions, it might not be the case. It is a good idea to backup yout settings to PC (via the MKTool) before installing the VibrationTest FC code.

After insatlling the FC code for the VibrationTest, the LC-Display in the MKTool will look like this:

LCDisplay.jpg

It is normal that a there is a warning for a missing BL-Ctrl. When you have 4 motors for example, it should complain that it did not find motor 5.

Starting the VibrationTest tool

In the directory where you unzipped the tool, dubbleclick VibrationTestGui.py (in case of the Python version) or VibrationTestGui.exe

Using the VibrationTest tool





Checking the reliability/accuracy of the results

Before you start, it is good to check the reliability of the test and setup.

You should alway start with a sweep and look at different sensors. If the vibrations is rather constant over motor-speed, the combination might be well balanced or you might not be measuring what you are hoping to measure. In this case, sticking some tape to the prop should should unbalance it and you should see a difference.
You can have a look at the recorded signals, the filtered signals and perhaps the spectrum. The picture below shows an example of (raw) a signal of good quality:

GoodSignal.jpg


The signal below is regular but goes slowly up and down. This is not a big problem as this will be filtered out later; this is still good:

MediumSignal.jpg


The signal in the next picture is of low quality. Propably other components than the motor are vibrating:

BasSignal.jpg



If the signals seem ok, you can repeat the sweep multiple times, using one of the sensors. Each time you should get similar results. Results will never be 100% the same.

Another test you should do, is let the tool measure multiple times at the same speed; for example "10*100,10*200". The measurement at the same speed should report the about the same amount of vibrations.

The figure below shows the result of such test with a "Roxxy 2824-34 / EPP1045 / 3s / Standard ESC" combination. All but the green line are from the Nick sensor. The black line are vibrations measured at speeds 130 and 185. The other lines are sweeps. This does not look too bad.

acuracy1.jpg


(!) When the results are disappointing, one should experiment with the way the MK is attached. One could fix the MK more firmly to the desk or on the contrary allow more movement. One should also and make sure nothing else but the MK can vibrate.

It is also possible that the filter parameters might not be optimal for your setup. In the figure below I have almost disabled the filter and switched to "pp" measurement:

acuracy2.jpg


This is another example of such a test (Turnigy 2836-750 / APC 12x3.8 / 4s / TowerPro ESC):

acuracy3.jpg



Examples

Balancing example: Roxxy 2824-34 / EPP1045 / 3s / Standard ESC


Effect of prop position, Roxxy 2824-34 / EPP1045 3s / Standard ESC

The importance of the position of the propeller relative to the motor was first reported by RCGroups member "Old Man Mike", see this post. My tool also shows this effect. However, I observed that sometimes rotating the prop did not produce significant variations...

I discovered that when I first balance the prop as good as I can using the VibrationTest, rotating the prop produced very little difference.

I come to the conclusion that I need to deliberately unbalance the prop a bit in order to find the "sweet spot". I also observed that when I unbalance the prop by sticking some tape on one side of the prop the vibrations peak while they go trough a minimum when I stick some tape to the other side. I think this supports the theory that the slightly unbalanced prop can compensate for unbalances in the motor.

StudyRotation.jpg

On the X-asis the rotation of the prop in steps of 60 degrees. The red line is with a prop that I balanced before (needs some tape opposite to the prop size-markers). The green line shows vibrations when I attach an additional strip of tape (so unbalancing it). The blue line shows what happens when I attach tape to the other side (where the markers are).

Balancing example: Turnigy 2836-750 / APC 12x3.8 / 4s / TowerPro ESC


Mk2BalancingExample1.jpg
The red line is the initial balancing. The prop seemed best balanced with no additional tape.
The green line are the measurement while rotating the prop (steps of 45 degrees)
The blue line is the re-balancing, due to the repositioning of the prop the results are better. The first 3 measurements showed that no tape produced the best results. In the last 3 measurements of the blue line, I experimented with smaller strips and this produced the best result.

Influence of ME ACC capacitors


This example shows why the VibrationTest does not work in combination with FlightControl ME boards. ME boards have bigger capacitors on the ACC lines and these suppress the signal we are interested in. 1.3 boards have 0.1 uF capacitors while ME has 1 uF capacitors.

To be sure that the issue was due to these capacitors I replaced one of the capacitors and performed some measurements. The first picture below shows the raw signal without capacitor (0uF). The next picture shows the signal with a 0.1uF capacitor, so this corresponds with the capacitor used on 1.3 boards. For the last picture a 1uF capacitor (so the normal value for an ME board) was installed. As you can see the signal is completely suppressed...

http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0uF.jpg http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0d1uF.jpg http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-1uF.jpg


The pictures below show the spectra of the same signals. As you can see, the 0.1uF cap already filters a lot but leaves the vibration signal visible.

http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0uF-spectrum.jpg http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-0d1uF-spectrum.jpg http://www.rc-flight.be/VibrationTest/Images/ME-Acc-Cap-1uF-spectrum.jpg



Changelog

Version

Date

Changes

1.2

17/11/2009

- Ability to measure Gyro sigals
- Tool to measure RPM

1.0

24/10/2009

= 0.9 RC4

0.9 RC4

21/10/2009

- FC code: ignore mixing table so that all motors always work

0.9 RC3

17/10/2009

- Fixed limitation of 4 motors (not tested)
- More parameter checking and clear error reporting
- Support to connect to NC
- Fixed exception at start of measurement



Older versions

  • 1.0

VibrationTest_1_0.zip
VibrationTestExe_1_0.zip



Links

Used Libraries and Tools

Technical references


  • [laden | anzeigen] (16.09.2014 11:33, 56.9 KB) [[attachment:BasSignal.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 40.0 KB) [[attachment:GoodSignal.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 24.6 KB) [[attachment:LCDisplay.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 49.2 KB) [[attachment:MediumSignal.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 37.4 KB) [[attachment:Mk2BalancingExample1.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 93.2 KB) [[attachment:PreviewGui.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 86.5 KB) [[attachment:PreviewGui2.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 33.9 KB) [[attachment:StudyRotation.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 36.6 KB) [[attachment:StudyRotations.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 87.5 KB) [[attachment:VibTestBanner.gif]]
  • [laden | anzeigen] (16.09.2014 11:33, 38.8 KB) [[attachment:VibTestBanner_small.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 52.9 KB) [[attachment:VibrationTest_0_0.zip]]
  • [laden | anzeigen] (16.09.2014 11:33, 47.9 KB) [[attachment:acuracy1.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 48.6 KB) [[attachment:acuracy2.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 48.4 KB) [[attachment:acuracy3.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 57.5 KB) [[attachment:calc.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 79.0 KB) [[attachment:cmdLine.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 128.5 KB) [[attachment:mk1InTest.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 90.7 KB) [[attachment:mk2InTest.jpg]]
  • [laden | anzeigen] (16.09.2014 11:33, 30.6 KB) [[attachment:test.jpg]]
 Alle Dateien | Ausgewählte Dateien: löschen verschieben auf Seite kopieren auf Seite