Unterschiede zwischen den Revisionen 9 und 13 (über 4 Versionen hinweg)

This page as an PDF-Document? Click on that Symbol and wait a little moment... --->

Shutter Cable

Eletronic schutter cable for cameras

High-quality cameras (eg SLR, Canon G11, EOS 5D etc.) usually have an input for a remote trigger.
A trigger cable for these cameras can be easily built, which can be controlled by the FlightControl.
A blue LED on the Shuttercable signals the switching process.

Set

The Shuttercable-Set consists of:

A board with optocouplers and LEDs
A cable to connect the camera (Set1 = 2,5mm plug / Set2 = N3 plug)
A two-core cable for connection to the flight control
Transparent shrink tube


Shuttercable with 2.5mm-Plug	Shuttercable with N3-PLug

Connect the cable - Set 1 = 2.5mm plug

Strip the cable

Connection

INFO: The kit can be supplied with different cable colors.
Each of the colors in the assignment as follows:

Function		Version I (yellow, blue, white)	connect with	Version II (yellow, red, white)	connect with	Version III (black, red, white)	connect with
GND	=>	yellow	Out -	Gelb	Out -	Schwarz	Out -
Focus	=>	blue	Out +	Weiss	Out +	Weiss	Out +
Trigger	=>	white	Out +	Rot	Out +	Rot	Out +

The last booth cables (blue + white) are connected together. So the camera gets the same command to Focus and Shoot.

The red cable:

red cable = In+
black marked cable = In-

Shrinking

Connect the cable - Set 2 = N3 plug

Strip the cable

Connection

Each of the colors in the assignment as follows:

Function		Version I (yellow, blue, white)	connect with
GND	=>	white	Out -
Focus	=>	red	Out +
Trigger	=>	yellow	Out +

The red cable:

red cable = In+
black marked cable = In-

Shrinking

Connect to the FlightControl

The red cable is connected to the transistor outputs "Out1" or "Out2" (top row of SV2).
$/!\$ The red wire of the cable is always in the middle.


"Out1"	"Out2"

The outputs Out1 and Out2 can be used.

Trigger

The Shuttercable is connected in this example to "Out2".
The trigger can be controlled as follows:

Adjustable interval after engine start

set interval and fixed bit pattern
Here settings for Out2: fixed interval (30)
Flash patterns is active only when the motors run
$/!\$ Values below 6 and over 220 result in an static signal. If you need a blinking interval, please use values between 6-220

Using switches on the remote control

Select a potentiometer instead of the interval
Settings for this Out2: Poti4 assigned

See Koptertool

Schematic

Optocoupler

An optocoupler provides electrical isolation between flight control and camera.

It protects the camera against damage in case of faulty connection or overvoltage.

The optocoupler operates almost like a switch.

-  ⇤ ← Revision 9 vom 11.04.2012 13:45 → 
  Größe: 6081
  Autor: LotharF
  Kommentar:
+   ← Revision 13 vom 19.09.2013 16:11 → ⇥
  Größe: 10902
  Autor: LotharF
  Kommentar:
-Gelöschter Text ist auf diese Art markiert.
+Hinzugefügter Text ist auf diese Art markiert.
 Zeile 1:
+#acl AdminGroup:read,write,revert EditorsGroup:read,write,revert All:read

||<class="MK_TableNoBorder">This page as an '''PDF-Document'''? Click on that Symbol and wait a little moment... ---> ||<class="MK_TableNoBorder"><<PDFIcon>>||
-Zeile 2:
+Zeile 6:
-||<class="MK_Nav_Header">[[en/MK-Board|MikroKopter-Boards]]||
-Zeile 7:
+Zeile 10:
-Zeile 11:
+Zeile 13:
+<<BR>>
-Zeile 12:
+Zeile 15:
+See also: [[en/MK-Board|MikroKopter-Boards]]
-Zeile 17:
+Zeile 21:
-Zeile 19:
+Zeile 24:
-High-quality cameras (eg SLR, Canon G11, etc.) usually have an input for a remote trigger.
+High-quality cameras (eg SLR, Canon G11, EOS 5D etc.) usually have an input for a remote trigger.<<BR>>
A trigger cable for these cameras can be easily built, which can be controlled by the FlightControl.<<BR>>
A blue LED on the Shuttercable signals the switching process.<<BR>><<BR>>
-Zeile 21:
+Zeile 28:
-A trigger cable for these cameras can be easily built, which can be controlled by the FlightControl.
+[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71745&g2_serialNumber=2|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71748&g2_serialNumber=4}}]]<<BR>><<BR>>
-Zeile 23:
+Zeile 30:
-[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_Cam.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71747}}]]
+###################################################################################################################################################################################################
-Zeile 25:
+Zeile 32:
-Where to buy: [[https://www.mikrocontroller.com/index.php?main_page=product_info&cPath=110&products_id=566|Shop-Link]]

== Set ==
The [[https://www.mikrocontroller.com/index.php?main_page=product_info&cPath=110&products_id=566|set]] consists of:
+= Set =
The Shuttercable-Set consists of:
-Zeile 30:
+Zeile 35:
- * A black cable with 90° 2,5mm jack
+ * A cable to connect the camera (Set1 = 2,5mm plug / Set2 = N3 plug)
-Zeile 34:
+Zeile 39:
-[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_Einzeln.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71754}}]]
+||<class="MK_TableNoBorder">[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71752&g2_serialNumber=4|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71755&g2_serialNumber=7}}]]||<class="MK_TableNoBorder">[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114713&g2_serialNumber=3|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114716&g2_serialNumber=6}}]]||
||<class="MK_TableNoBorder":>Shuttercable with 2.5mm-Plug||<class="MK_TableNoBorder":>Shuttercable with N3-PLug||
-Zeile 36:
+Zeile 42:
-== Connect the cable ==
-Zeile 38:
+Zeile 43:
-== Strip the cable ===
+###################################################################################################################################################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>
-Zeile 40:
+Zeile 46:
-[[http://gallery.mikrokopter.de/main.php/v/tech/Abisolieren.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71770}}]]
+= Connect the cable - Set 1 = 2.5mm plug =
-Zeile 42:
+Zeile 48:
-=== Connection ===
[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_Belegung.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=81544}}]]
+== Strip the cable ==
-Zeile 45:
+Zeile 50:
- * Red wire: black cable labeled " In- "
 * Black cable Version I: blue and white on " Out+ "; Yellow to " Out- "
 * Black cable Version II: red and white on " Out+ "; Yellow to " Out- "
 * Black cable Version III: red and white on " Out+ "; Black to " Out- "
+[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114764&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114768&g2_serialNumber=2}}]]
[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114769&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114773&g2_serialNumber=2}}]]
-Zeile 50:
+Zeile 53:
-[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_Bau.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71768}}]]
+== Connection ==

[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=81543&g2_serialNumber=2|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114777&g2_serialNumber=2}}]]
<<BR>><<BR>>

<!> '''INFO:''' 
The kit can be supplied with different cable colors.<<BR>>
Each of the colors in the assignment as follows:
<<BR>><<BR>>

||<-2 bgcolor="#9FC6E7":>'''Function'''||<width="10px" class="MK_TableNoBorder">||<width="200px" bgcolor="#9FC6E7":>'''Version I'''<<BR>>(yellow, blue, white)||<bgcolor="#9FC6E7":>connect<<BR>>with||<width="10px" class="MK_TableNoBorder">||<width="200px" bgcolor="#9FC6E7":>'''Version II'''<<BR>>(yellow, red, white)||<bgcolor="#9FC6E7":>connect<<BR>>with||<width="10px" class="MK_TableNoBorder">||<width="200px" bgcolor="#9FC6E7":>'''Version III'''<<BR>>(black, red, white)||<bgcolor="#9FC6E7":>connect<<BR>>with||
||<bgcolor="#F7EC80">GND     ||<bgcolor="#F7EC80":>=>||<class="MK_TableNoBorder">||<:>yellow ||<:bgcolor="#F7EC80":>'''Out -'''||<class="MK_TableNoBorder">||<:>Gelb ||<:bgcolor="#F7EC80":>'''Out -'''||<class="MK_TableNoBorder">||<:>Schwarz||<:bgcolor="#F7EC80":>'''Out -'''||
||<bgcolor="#F7EC80">Focus   ||<bgcolor="#F7EC80":>=>||<class="MK_TableNoBorder">||<:>blue ||<:bgcolor="#F7EC80":>'''Out +'''||<class="MK_TableNoBorder">||<:>Weiss||<:bgcolor="#F7EC80":>'''Out +'''||<class="MK_TableNoBorder">||<:>Weiss  ||<:bgcolor="#F7EC80":>'''Out +'''||
||<bgcolor="#F7EC80">Trigger||<bgcolor="#F7EC80":>=>||<class="MK_TableNoBorder">||<:>white||<:bgcolor="#F7EC80":>'''Out +'''||<class="MK_TableNoBorder">||<:>Rot  ||<:bgcolor="#F7EC80":>'''Out +'''||<class="MK_TableNoBorder">||<:>Rot    ||<:bgcolor="#F7EC80":>'''Out +'''||
<<BR>>

The last booth cables (blue + white) are connected together. So the camera gets the same command to Focus and Shoot.<<BR>><<BR>>


The red cable:
 * red cable = '''In+'''
 * black marked cable = '''In-'''
<<BR>><<BR>>

[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_Bau.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71768}}]]<<BR>><<BR>>
-Zeile 54:
+Zeile 81:
-=== Shrinking ===
+== Shrinking ==
-Zeile 58:
+Zeile 86:
-=== Assignment of the cable (Version I) ===
 * Yellow: GND
 * Blue: focus (when connecting from blue to yellow)
 * White: Trigger (when connecting from blue to yellow)
In the ShutterCable blue and white are combined. So the camera gets the instruction to focus and release at the same time.
-Zeile 64:
+Zeile 87:
-=== Assignment of the cable (Version II) ===
 * Yellow: GND
 * White: focus (when connecting from blue to yellow)
 * Red: Trigger (when connecting from blue to yellow)
In the ShutterCable red and white are combined. So the camera gets the instruction to focus and release at the same time.
-Zeile 70:
+Zeile 88:
-=== Assignment of the cable (Version III) ===
 * Black: GND
 * White: focus (when connecting from blue to yellow)
 * Red: Trigger (when connecting from blue to yellow)
In the ShutterCable red and white are combined. So the camera gets the instruction to focus and release at the same time.
+###################################################################################################################################################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>

= Connect the cable - Set 2 = N3 plug =

== Strip the cable ==

[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114764&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114768&g2_serialNumber=2}}]]
[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114769&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114773&g2_serialNumber=2}}]]

== Connection ==

[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114703&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114707&g2_serialNumber=2}}]]
<<BR>><<BR>>

Each of the colors in the assignment as follows:
<<BR>><<BR>>

||<-2 bgcolor="#9FC6E7":>'''Function'''||<width="10px" class="MK_TableNoBorder">||<width="200px" bgcolor="#9FC6E7":>'''Version I'''<<BR>>(yellow, blue, white)||<bgcolor="#9FC6E7":>connect<<BR>>with||
||<bgcolor="#F7EC80">GND     ||<bgcolor="#F7EC80":>=>||<class="MK_TableNoBorder">||<:>white ||<:bgcolor="#F7EC80":>'''Out -'''||
||<bgcolor="#F7EC80">Focus   ||<bgcolor="#F7EC80":>=>||<class="MK_TableNoBorder">||<:>red ||<:bgcolor="#F7EC80":>'''Out +'''||
||<bgcolor="#F7EC80">Trigger||<bgcolor="#F7EC80":>=>||<class="MK_TableNoBorder">||<:>yellow||<:bgcolor="#F7EC80":>'''Out +'''||
<<BR>><<BR>>

The red cable:
 * red cable = '''In+'''
 * black marked cable = '''In-'''
<<BR>><<BR>>

[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114687&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114689&g2_serialNumber=2}}]]<<BR>><<BR>>

[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114693&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114695&g2_serialNumber=2}}]]

== Shrinking ==

[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114698&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114700&g2_serialNumber=2}}]]


###################################################################################################################################################################################################
<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>
-Zeile 77:
+Zeile 130:
-The cable is connected to the transistor outputs (top row of SV2):
-Zeile 79:
+Zeile 131:
-[[http://gallery.mikrokopter.de/main.php/v/tech/FC_ME_Connections.gif.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=38789}}]]
+The red cable is connected to the transistor outputs "Out1" or "Out2" (top row of SV2).<<BR>>
/!\ The red wire of the cable is always in the middle.<<BR>><<BR>>
-Zeile 81:
+Zeile 134:
-[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_FC_001.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71778}}]]
+[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82437&g2_serialNumber=4|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97121&g2_serialNumber=2}}]]


||<class="MK_TableNoBorder">[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114810&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114813&g2_serialNumber=2}}]]||<class="MK_TableNoBorder">[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114814&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=114817&g2_serialNumber=2}}]]||
||<class="MK_TableNoBorder":>"Out1"||<class="MK_TableNoBorder":>"Out2"||
<<BR>><<BR>>
-Zeile 85:
+Zeile 143:
-/!\ The red wire of the cable is always in the middle
-Zeile 88:
+Zeile 146:
+The Shuttercable is connected in this example to "Out2".<<BR>>
-Zeile 108:
+Zeile 168:
-[[http://gallery.mikrokopter.de/main.php/v/tech/SchutterCable_Schaltplan.gif.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71765}}]]
+[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71763&g2_serialNumber=2|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=71765&g2_serialNumber=2}}]]
-Zeile 111:
+Zeile 171:
-Zeile 117:
+Zeile 178:
-== Building yourself without the set ==

If you want to build the cable yourself, it can also be realized without the LED

[[http://www.mikrocontroller.com/files/ShutterCable1.jpg|{{http://www.mikrocontroller.com/files/ShutterCablekl.jpg}}]]

You would need:
 * A servo cable
 * A resistor (eg 330Ohm Reichelt: SMD1/4W 330)
 * An optocoupler (for example, Reichelt: LTV-356T SMD)
 * A jack (for example, Reichelt: KSS25)
 * A small piece of breadboard PCB (eg Reichelt: H25PR050)