MikroKopter

This page is being edited 18.4.09


Introduction

Once you have built your MikroKopter (MK) and are happy with the mechanics and construction, it is important that before you try to get it off the ground you set up the boards and controls. Unlike most other flying machines, the MikroKopter relies solely on electronics to keep it under control as it has no control flying surfaces. It is vitally important that the various parameters are set before you try to fly. :)

Initial Check

Connect the power supply to the MK and switch on. The motors will all rotate one after the other and beep. The following LEDs will be on

Green LED on each of the BL-Ctrls - If not goto http://www.mikrokopter.de/ucwiki/en/BL-Ctrl_Manual
Green LED on the Flight Controller - If not goto http://www.mikrokopter.de/ucwiki/en/FlightCtrlManual
Red LED on the MK3 Mag - If not goto http://www.mikrokopter.de/ucwiki/en/MK3Mag
Green Led on the GPS - If not goto http://www.mikrokopter.de/ucwiki/en/MKGPS
Red and green LEDs on the Navi Board - If not goto http://www.mikrokopter.de/ucwiki/en/NaviCtrl

If all the above are correct then the MK can be setup using the MK tool http://www.mikrokopter.de/ucwiki/en/MikroKopter-Tool?action=show&redirect=en%2FMikroKopterTool

Connecting the Sercon to the PC


The MK tool will only work on a PC using a 'real' serial port. Using a USB - Serial port converter will not work properly and may cause problems. If your PC does not have a serial port than a PCMICA adaptor will work.


/!\ ToDo: Screenshots

Writing and Reading Settings from the MK Tool

The Flight Controller (FC) can store up to 5 different sets of parameters called "Settings" . One parameter set can be used at any one time and is selected prior to starting the MK by moving the sticks to specific positions. The MK tool will display any one of these 5 parameters sets stored in the FC board by reading them from the FC board. When the MK tool is activated the last used 'Setting' is displayed. The 'Setting' number is shown just above the bottom left "Parameterset" .
http://gallery.mikrokopter.de/main.php/v/tech/config1_001.jpg.html
In this example Setting 3 I have renamed to 'Norm Camera'
The default settings are:

The values of any of the 5 Settings can be saved onto the PC by clicking on the "Save' button
To load any previous saved 'Settings' into the MK tool click on the "Load" button and locate the file. The MK tool will now display the 'Settings' from the PC. Any changes you make to these parameters will not be stored on the FC until you "Write" them to the FC by clicking on the "Write" button. The MK will beep 1 for 'Setting 1', twice for 'Setting 2' etc. This will overwrite all the values for that 'Setting' onto the FC board.
To see the values now stored on the FC board click on the "Read" button.
You may like to leave the 3 default settings alone but make some changes and write them to Setting 4 or 5 as follows:

/!\ A word of warning - Changing parameter settings can have a dramatic effect on the control of your MK. While it is necessary to change some parameters to set up the MK, it is not recommended that you make drastic changes without first understanding how the values interact with the MK's control. Changes to some values will not have the same effect on your MK as on another due to differences in weight, motor spacing, props and operation etc. Always make small changes and note the effect.

Setting the Transmitter channels

The transmitter (TX) channels must be configured in the MK tool so that the correct channel controls the correct function. It sounds obvious but, since there are different Modes on some TX's the channels will need to be assigned to correspond the Mode you have selected.

http://gallery.mikrokopter.de/main.php/v/tech/config1.jpg.html

/!\ ToDo: Screenshots and Instructions

Checking direction of the Props

For an MK with 4 motors the direction of the props are

For other motor configurations http://www.mikrokopter.com/ucwiki/mkm

Each motor is connected by 3 cables. To change the direction of rotation of the motor simply swap any 2 connections.

Calibrating the Compass


The compass board is a magnetic compass that reads the earths magnetic fields. It also reads any other magnetic fields that are in close proximity. It is therefore very important that all strongly magnetic devices are moved away from this board. The buzzer should be mounted on one of the arms of the MK and not on the FC board. It is also better to calibrate the compass in an area that is magnetic interference free. Places to avoid are:

To set up the compass you must first make sure that the YAW TX trim setting is set to zero on the MK tool. NB -This is not the same as setting the trim to zero on the TX only.
To set up the TX to be trimmed to zero

Calibration of the compass

<!> Important: When first operated, the MK3Mag needs to be correctly calibrated! Otherwise the NaviBoard will show you "Err:6 bad compass value".

Now it is (since Version FC:0.84) very easy to calibrate the compass with a "clicking sound" .
This method has the advantage that you doesn't have to hold the Kopter "perfect" horizontally.

IMPORTANT

The Nick- and Roll axis refers to the FlightCtrl, and not on the Mixer you use! The arrow of the FlightCtrl shows the Nick axis!

The Kopter should be calibrated outside, away from magnetic influences!
So please do not calibrate the Kopter directly next to a house, near power poles or metallic / magnetic surfaces.
Also, please take your cell etc. out of your pocket.

<!> The earth's magnetic field is not the same everywhere. That's the reason why you should calibrate the compass new if you change the place where you fly.
(e.g. from Germany to USA or from north to south America)

The calibration will be done in several steps:

Step

Function

Example View / Function

Step 1
Initiate compass calibration

Nick down

then

Throttle up + Yaw left

(The Kopter beeps 1x)

On a transmitter in MODE 2 it lokks like in that way:
https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=93577&g2_serialNumber=4

Step 2
Start Calibration

Pull Nick down 1x

(The Kopter beeps 2x and the clicking starts begins)

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97303&g2_serialNumber=2

Calibration of the X-Axis (Nick-Axis)

The Kopter with the front
(Arrow direction of the FlightCtrl)
pointing to the South or North.

Then

rotate the Kopter a couple times over the Nick-Axis until the buzzer stops with the clicking starts.

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97965&g2_serialNumber=2

Calibration of the Y-Axis (Roll-Axis)

Rotate the Kopter by 90°
The clicking starts again.

Rotate the Kopter a couple times over the Roll-Axis until the buzzer stops with the clicking starts.

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97969&g2_serialNumber=2

Step 3
Finish the calibration of the X and Y-Axis

Pull Nick 1x down

(The Kopter beeps 3x)

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97303&g2_serialNumber=2

Step 4
Start calibration of the Z-Axis

Pull Nick 1x down

(The Kopter beeps 4x and the clicking starts begin again)

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97303&g2_serialNumber=2

Calibration of the Z-Axis (Yaw-Axis)

INFO: Here it doesn't matter if the Kopter shows with the X or Y-Axis towards South (North).

Rotate the Kopter a few times over the Roll- or Nick-Axis until the buzzer stops with the clicking starts.

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97710&g2_serialNumber=2

Step 5
Finish the calibration of the Z-Axis.

Pull Nick 1x down

The Kopter confirms it with 2 beeps

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97303&g2_serialNumber=2



3. Now that the Kopter "beeped" 2x after a successful calibration that part is done.

  • If everything is OK the red LED stops lighting after a few seconds on the NaviCtrl V2.0 with integrated compass.
    If you use a NaviCtrl V1.1 with MK3Mag the red LED on the MK3Mag lights permanently.

DONE!

Videos

(German version)


(English version)


If the calibarion fails (compass still reports "invalid compass value"), you can take a look here: MagnetError

Setting the POTI Channels

These channels are used to control functions and servos on the MK such as:


It does not matter what functions these channels are used for, but what is important is that the POTI channel is not accidentally used to operate 2 functions at the same time by mistake.
Normally channels 1, 2, 3 and 4 are used to control GAS, YAW, NICK and ROLL, ie. the stick controls. The remaining 4 channels 5, 6, 7, and 8 are used for the POTI controls.
There are so many uses these channels can be used for it is not really possible to cover every variation. Here is how to assign a slider channel to control the camera tilt which may be used as a typical example.

/!\ ToDo:[[BR]

Initialisation of the GPS

The GPS board has 3 modes, OFF, POSITION HOLD and COMING HOME.
Setting up the board to be activated by the TX you must assign a channel to a POTI See 'Setting the POTI Channels' on this page.
http://gallery.mikrokopter.de/main.php/v/tech/gps1_001.jpg.html
The GPS can be activated by a slider on the TX, or better still a 3 position switch.
The board, even when OFF will search and detect satellites. For more about the GPS and Navi Control Boards see http://www.mikrokopter.com/ucwiki/en/NaviCtrl

/!\ ToDo:

Activating the Height Control

If you have a height control sensor fitted to the Flight Control board http://www.mikrokopter.com/ucwiki/en/heightsensor then you will need to assign the activation of the sensor in the MK Tool.
http://gallery.mikrokopter.de/main.php/v/tech/height1.jpg.html
The sensor reads barometric pressure and will hold an MK at a specific height within 2m or so. To activate this control you must assign a channel to control the ON/OFF of the sensor. This may be achieved by a switch or a slider on a POTI channel. See 'Setting the POTI Channels' on this page.
If you use a slider the slider does NOT control the height it simply controls the ON/OFF. The GAS or THROTTLE stick will control the height position. The height sensor will hold the MK at the that height even if the GAS is increased, it acts like a ceiling. Decreasing the GAS will make the MK descend, raising the GAS again will make the MK rise to the same position.

KategorieEnglish

MikroKopter: en/Setting_Up (zuletzt geändert am 23.09.2011 20:49 durch HolgerB)