⇤ ← Revision 1 vom 01.08.2012 12:47
Größe: 6383
Kommentar:
|
Größe: 6384
Kommentar:
|
Gelöschter Text ist auf diese Art markiert. | Hinzugefügter Text ist auf diese Art markiert. |
Zeile 9: | Zeile 9: |
* {{http://mikrokopter.de/images/deu.gif}} [[LanCtrl|deutsch]] | * {{http://mikrokopter.de/images/deu.gif}} [[LancCtrl|deutsch]] |
Shoplink: IR-Ctrl
IR-Ctrl V1.0 |
Inhaltsverzeichnis
LancCtrl Version 1.0
Shoplink: IR-Ctrl
video of usage
The LANC-Ctrl is a control board to control cameras or video-cameras via SONY LANC-Interface (like SONY cx730 / cx760).
The LANC control can also be connected to the FlightControl or stand alone on a receiver.
Via a ultrabright red LED the status of the camera is visible (Standby, REC, Photo,..)
The recording will be started via a switch on the remote control. And the recording will run until the switch is switched back to 'off'. That makes the recording much more safe compared with a the start/stop button via IR.
The following functions can be used:
Zoom-in & out (variable speeds - from very slow to very fast)
- REC Start/Stop
- Photo shutter (in Video and photo mode)
Technical Data
- Weight: approx.15g incl. cables
- Dimension: approx.30x20mm
- Cable length: Red-LED-Cable approx.30cm
- Cable length: SONY AV-Cable approx.30cm
- Cable length: Servo cable approx.30cm
IMPORTANT - Please read!
The LANC-Ctrl has two inputs - PPM1 + PPM2.
Do NOT connect this inputs at the same time to the FlightCtrl and the connected receiver!
Connect always booth inputs (PPM1+PPM2) either directly to the FlightCtrl OR the receiver.
To eliminate the destroying of the LANC-Ctrl and the FlightCtrl, the IR-Ctrl have now for the inputs only one PPM-Cable and one JR-Data cable (gray).
The powering of the IR-Ctrl is only to do with the PPM-Cable. The JR-Data cable have only the needed data connection. This cable is connected to the PPM contact.
Inputs/Outputs
The IR-Ctrl has got two PPM Inputs (PPM1 + PPM2). In that way a total of 4 functions (2 for each Input) can be triggered.
Via the pin-header the IR-Ctrl:
can be connected via the MK-USB to the KopterTool for updates,
- the LED can be connected,
ATTENTION: The plug of the LED must be connected in that way that the red side points upwards (pointing to the IC).
The connection - which switch?
The IR-Ctrl can be connected either way to the servo-outputs of the FlightCtrl or to a regular receiver with servo-outputs.
On the transmitter, the stages switch (REc/Photo) should be assigned to a 3-stage switch or poti. The Zoom must be assigned to a Poti.
Record and photos
Switch for recording:
- Pos.1 = Record off
- Pos.3 = Video recording (Attention: the camera must be in video mode, not photo mode!)
- From 'off' into middle position: Photos without video
- From 'rec' into middle position: Photos during video recording (for the cx730 or cx760 only possible in 25i or 50i video format)
Zoom
In and out-Zooming is possibe in eight different speeds.
Middle position ist the idle position.
If the switch is in 'Rec' position and the camera can't record (SD-card full), the Zoom doesn't work correctly.
Connection Servo-Output FlightCtrl
The IR-Ctrl can be connected to the servo-outputs "Servo3" and "Servo4" (Link) on the FlightCtrl .
Those both outputs you can control directly with a channel (Poti1-8) (Link) or via the switch outputs (Out1/Out2).
Connection to Receiver
If you control the camera separatly with a second transmitter and an additional receiver you can connect here also the IR-Ctrl.
It is also possible, using the transmitter Graupner MC-32 HoTT, to set two more channels and get them via the receiver, i.e. the GR32.
IMPORTANT:
If you connect the IR-Ctrl direct to the receiver (as shown here in the picture) you must adjust the channel transfer on your receiver!
- KategorieMK-Baugruppe/de