Größe: 12323
Kommentar:
|
Größe: 11450
Kommentar:
|
Gelöschter Text ist auf diese Art markiert. | Hinzugefügter Text ist auf diese Art markiert. |
Zeile 1: | Zeile 1: |
#acl AdminGroup:read,write,revert dl2yak:read,write,revert All: <<RedBox('''INTERNE SEITE''' - vertraulich)>> |
|
Zeile 22: | Zeile 19: |
'''Shoplink: ''' <<BR>><<BR>> |
'''Shoplink: '''[[https://www.mikrocontroller.com/index.php?main_page=product_info&cPath=110&products_id=688|IR-Ctrl]] <<BR>><<BR>> {{https://www.mikrocontroller.com/images/IR_Ctrl_2.JPG}} |
Zeile 47: | Zeile 45: |
Via the pin-header the IR-Ctrl can be: * connected via the MK-USB to the !KopterTool for updates, * the IR-LED been connected, * via jumper the remote control code been teached. |
Via the pin-header the IR-Ctrl: * can be connected via the MK-USB to the !KopterTool for updates, * the IR-LED can be connected, * the remote control code can be teached via the jumper. |
Zeile 136: | Zeile 134: |
== The switch commands == As described there are 4 opportunities for the reproduction of IR commands.<<BR>> An IR-signal can be transmitted permanently, one time, every second or every three seconds.<<BR>> Via the jumpers you are able to set how the IR-signal should be transmitted: <<BR>><<BR>> ||<:rowbgcolor="#9FC6E7">Timing = Permanetly||<:>Timing = One Time||<:>Timing = One Sekunde||<:>Timing = Three seconds|| ||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115178&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115345&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115189&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115347&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115204&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115350&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115210&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115351&g2_serialNumber=2}}]]|| ||<:-4>To enlarge => Click on the image|| <<BR>><<BR>><<BR>> The introduction of the learn-function will start by plug-in the "Teach"-Jumper: <<BR>><<BR>> ||<:rowbgcolor="#9FC6E7">Teach = Permanently||<:>Teach = One Time||<:>Teach = One Second||<:>Teach = Three Seconds|| ||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115184&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115346&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115194&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115348&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115199&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115349&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115216&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115352&g2_serialNumber=2}}]]|| ||<:-4>To enlarge => Click on the image|| <<BR>><<BR>><<BR>><<BR>> ######################################################################################################################################################################### |
######################################################################################################################################################################### |
Zeile 173: | Zeile 150: |
As described there are 4 opportunities for the reproduction of IR commands.<<BR>> An IR-signal can be transmitted permanently, one time, every second or every three seconds.<<BR>><<BR>> |
|
Zeile 202: | Zeile 182: |
{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115434&g2_serialNumber=2}}<<BR>><<BR>> |
|
Zeile 217: | Zeile 200: |
= IR-Sensor = The IR-Sensor can be mounted in front of the IR-receiver of the camera / video camera.<<BR>> To fix the IR-Sensor you can use e.g. a strip of tape.<<BR>><<BR>> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115439&g2_serialNumber=2}} ######################################################################################################################################################################### |
|
Zeile 220: | Zeile 213: |
Via the KopterTool it is possible to refresh the IR-Ctrl with new Updates or reset back into the delivery status.<<BR>><<BR>> | Via the KopterTool it is possible to refresh the IR-Ctrl with new Updates or reset back into the delivery status.<<BR>> (After a reset, the default functions are restored) <<BR>><<BR>> |
Zeile 224: | Zeile 218: |
== IR-Code Import/Export == It is possible to read and store the IR data of the IR-Ctrl.<<BR>> Also it is possible to import such stored data.<<BR>><<BR>> In the terminal window of the !KopterTool you can "click" with the right mouse button into the gray area.<<BR>> Now you can see the context menu where you can choose import or export.<<BR>><<BR>> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=115425&g2_serialNumber=1}} <!> in case these both menu items are not shown: * Start communication between KopterTool and IR-Ctrl by clicking to "Debug". Then the KopterTool notices, that it is connected to the IR-Ctrl. * a KopterTool since 1.79a is reqiured |
IR-Ctrl V1.0 |
Inhaltsverzeichnis
IR-Ctrl Version 1.0
Shoplink: IR-Ctrl
The IR-Ctrl is a control board to trigger cameras or video-cameras via infra-red.
For that reason that the control board works also as a teachable remote control any camera/video-camera function, such as zooming, can be programmed.
Only the remote control of the used camera/camcorder is necessary.
For the delivery the IR-Ctrl is already pre-programmed for the video-camera Sony CX730, the NEX-5 and for the Canon EOS-Models.
The following 4 functions can be used:
- Zoom-in
- Zoom-out
- REC Start/Stop
- Trigger photo
Inputs/Outputs
The IR-Ctrl has got two PPM Inputs (PPM1 + PPM2). In that way a total of 4 functions (2 for each Input) can be triggered.
Via the pin-header the IR-Ctrl:
can be connected via the MK-USB to the KopterTool for updates,
- the IR-LED can be connected,
- the remote control code can be teached via the jumper.
ATTENTION: The plug of the IR-LED must be connected in that way that the red side points upwards (pointing to the IC).
The connection - which switch?
The IR-Ctrl can be connected either way to the servo-outputs of the FlightCtrl or to a regular receiver with servo-outputs.
On your transmitter you can use for the different functions i.e. a 3-way-switch, a Poti or (while using a secong transmitter in TrainerMode) one of the sticks.
How works it to trigger the 4 functions?
Each input of the IR-Ctrl can perform 2 functions. Möchte man also beide Eingänge (PPM1+2) mit allsen 4 Funktionen Nutzen, kann man beispielsweise zwei 3-fach Schalter hierfür nutzen.
So that the IR-Ctrl detects which function should be executed the position of the switching channel is been used for that purpose.
This should be clarified in an example with a 3-way-switch:
A 3-way-switch has got 3 switch positions.
In the first switch position is thze channel on "Low" (0), in the second position on "Middle position" (127) and in the third position on "High" (254).
The middle position signals the IR-Ctrl the "Idle position". If you switch now to the switch position "Low" or "High" (Position 1 or 3) the first or second function will be triggered.
The functions are assigned as follows:
- PPM1
Low => Function 1 (green LED flashes during programming 1x with interruption)
High => Function 2 (green LED flashes during programming 2x with interruption)
- PPM2
Low => Function 3 (green LED flashes during programming 3x with interruption)
High => Function 4 (green LED flashes during programming 4x with interruption)
Of course, you can also use a button or a switch.
Here then, depends on the switch position / operation of the button, a function will be done permanently.
Connection Servo-Output FlightCtrl
The IR-Ctrl can be connected to the servo-outputs "Servo3" and "Servo4" (Link) on the FlightCtrl .
Those both outputs you can control directly with a channel (Poti1-8) (Link) or via the switch outputs (Out1/Out2).
Connection to Receiver
If you control the camera separatly with a second transmitter and an additional receiver you can connect here also the IR-Ctrl.
It is also possible, using the transmitter Graupner MC-32 HoTT, to set two more channels and get them via the receiver, i.e. the GR32.
IMPORTANT:
If you connect the IR-Ctrl direct to the receiver (as shown here in the picture) you must adjust the channel transfer on your receiver!
The programming
If you have got a different camera or you don't want to use the standard functions you can program the IR-Ctrl via the pin-header and the IR-receiver on the underside with new commands.
Here you can set if an IR-command
- permanently
- one time
- every second
- or every 3 seconds
should be transmitted.
Teaching new IR-Commands
Step1:
The inputs of the IR-Ctrl "PPM1" + "PPM2" should be connected to the appropriate slot on the FlightCtrl or the Output/Channel of the receiver.
The FlightCtrl (or the receiver if not connected to the FlightCtrl !) need to be supplied with power. The green LED on the IR-Ctrl is lighting.
Step2:
As described there are 4 opportunities for the reproduction of IR commands.
An IR-signal can be transmitted permanently, one time, every second or every three seconds.
Choose desired timing:
Timing = Permanently |
Timing = One Time |
Timing = One Second |
Timing = Three seconds |
Step3:
Start programming: Attach jumper "Teach" => The green LED on the IR-Ctrl is flashing in second intervals:
Teach = Permanently |
Teach = One Time |
Teach = One Second |
Teach = Three Seconds |
Step4:
Briefly operate Switch/Button/Stick on the transmitter which function should be triggered and move it back again into the original position:
LED on the IR-Ctrl goes off for a short time and starts flashing 1-4x (depends on the operated Input Hi/Lo) with a short interruption.
(INFO: A 3-way-switch should be operated from the middle-position.)
Step5:
Point the remote control of the Camera/Video-Camera to the sensor on the underside of the IR-Ctrl and press the desired function/button.
The red LED on the IR-Ctrl acknowledges the input with a unique flash - The green LED flashes again in second intervals.
Step6:
Disconnect jumper "Teach".
By disconnecting the jumper you finish the programming.
To program the remaining three of all 4 functions you need to continue with Step2.
IR-Sensor
The IR-Sensor can be mounted in front of the IR-receiver of the camera / video camera.
To fix the IR-Sensor you can use e.g. a strip of tape.
Reset IR-Ctrl / Updates
You can connect the IR-Ctrl, like all other MikroKopter-Boards, to the MK-USB.
Via the KopterTool it is possible to refresh the IR-Ctrl with new Updates or reset back into the delivery status.
(After a reset, the default functions are restored)
IR-Code Import/Export
It is possible to read and store the IR data of the IR-Ctrl.
Also it is possible to import such stored data.
In the terminal window of the KopterTool you can "click" with the right mouse button into the gray area.
Now you can see the context menu where you can choose import or export.
in case these both menu items are not shown:
Start communication between KopterTool and IR-Ctrl by clicking to "Debug". Then the KopterTool notices, that it is connected to the IR-Ctrl.
a KopterTool since 1.79a is reqiured
- KategorieMK-Baugruppe/de