|
Größe: 8357
Kommentar:
|
Größe: 9799
Kommentar: Montage Stiftleisten etc hinzugefügt.
|
| Gelöschter Text ist auf diese Art markiert. | Hinzugefügter Text ist auf diese Art markiert. |
| Zeile 8: | Zeile 8: |
| == Top Side== | == Top Side == |
| Zeile 22: | Zeile 23: |
| == Bottom Side== | == Bottom Side == |
| Zeile 25: | Zeile 26: |
| 1 - 10pin connector for MK-USB or NaviCtrl connection<<BR>> 2 - Pressure Sensor (cut out of sensor connector points to the right)<<BR>> 3 - 6pin connector for servo 2 and Servo 3<<BR>> 4 - 6pin connector for servo 4 and servo 5<<BR>> 5 - DC/DC voltage regulator 5v Recom for Flight Controller<<BR>> 6 - DC/DC voltage regulator 5v Recom for servos<<BR>> 7 - 6pin connector for NaviCtrl<<BR>> 8 - 6pin connector for servo 1 and switchable J16/J17 connectors<<BR>> 9 - I2C connector (C/D) for BL Controllers<<BR>> 10 - JET (If you are using the Jeti Satellite receiver you will have to bridge these two connectors)<<BR>> 11 - 5pin connector (5V, GND, 3V, RX,TX) | 1 - 10pin connector for MK-USB or NaviCtrl connection<<BR>> 2 - Pressure Sensor (cut out of sensor connector points to the right)<<BR>> 3 - 6pin connector for servo 2 and Servo 3<<BR>> 4 - 6pin connector for servo 4 and servo 5<<BR>> 5 - DC/DC voltage regulator 5v Recom for Flight Controller<<BR>> 6 - DC/DC voltage regulator 5v Recom for servos<<BR>> 7 - 6pin connector for NaviCtrl<<BR>> 8 - 6pin connector for servo 1 and switchable J16/J17 connectors<<BR>> 9 - I2C connector (C/D) for BL Controllers<<BR>> 10 - JET (If you are using the Jeti Satellite receiver you will have to bridge these two connectors)<<BR>> 11 - 5pin connector (5V, GND, 3,3V, RX,TX) |
| Zeile 29: | Zeile 40: |
| Zeile 30: | Zeile 42: |
| . Connect the orange Receiver cable on 3V, black to G and gray to RX<<BR>> 12 - connection for the buzzer (BUZ-/BUZ+)<<BR>> 13 - Connection for PPM receiver (GN-brown, +5V-red, PPM-orange)<<BR>> 14 - Ground (GND) connection for the Flight Controller<<BR>> 15 - Positive (+) connection for the Flight Controller (if a power switch is being used)<<BR>> 16 - Positive (+) connection for the Flight Controller (without a power switch)<<BR>> [[FlightCtrl_ME_2_0#Anschl.2BAPw-sse|also see info on FC2.0]] |
. Connect the orange Receiver cable on 3,3V, black to G and gray to RX<<BR>> 12 - connection for the buzzer (BUZ-/BUZ+)<<BR>> 13 - Connection for PPM receiver (GN-brown, +5V-red, PPM-orange)<<BR>> 14 - Ground (GND) connection for the Flight Controller<<BR>> 15 - Positive (+) connection for the Flight Controller (if a power switch is being used)<<BR>> 16 - Positive (+) connection for the Flight Controller (without a power switch)<<BR>> == Mounting the plug connector, pressure sensor, elko == The FlightCtrl still has to be equipped with some components<<BR>><<BR>> [[http://gallery.mikrokopter.de/main.php/v/tech/FC21-mit-Bauteilen.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=73018}}]]<<BR>><<BR>> [[http://gallery.mikrokopter.de/main.php/v/tech/FC21-best__ckt1.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=73010}}]] [[http://gallery.mikrokopter.de/main.php/v/tech/FC21-best__ckt-2.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=73014}}]] <<BR>><<BR>> /!\ The FCV2.1 can with a 5-pin. Molex cables are connected to the power distributor. <<BR>> When using the Molexkabel between FlightCtrl and powerboard, you don't have to solder the I2C bus, the buzzer and the power cable to the FlightCtrl. <<BR>> Only the power cable for the receiver still has to be soldered to the FlightCtrl. <<BR>> The buzzer is connected directly to the appropriate solder points of the flow distributor (Buzzer / -). <<BR>> The I2C-bus and the voltage supply are provided from the power distribution over the Molex. <<BR>> Alternatively, the FC V2.1 can be connected with individual cable to the power distributor. <<BR>> <<BR>> |
| Zeile 58: | Zeile 87: |
| Hinweis: die Servoausgänge werden erst aktiviert, nachdem die Gyros kalibriert wurden (Gas/Gier-Knüppel so lange in die obere linke Ecke drücken, bis der Summer piepst und die grüne LED erlischt). | Attention: the servo outputs get activated after the calibration of the gyros. Push the throttle lever in the upper left corner until you hear the buzzer and the green LED turns off. |
| Zeile 114: | Zeile 143: |
| The 3V power connection for the satellite receiver is on the bottom side of the Flight Controller. | The 3,3V power connection for the satellite receiver is on the bottom side of the Flight Controller. |
| Zeile 119: | Zeile 148: |
| * orange to "3V" (positive) | * orange to "3,3V" (positive) |
| Zeile 149: | Zeile 178: |
| /!\ Die Benutzung der MikroKopter-Software ist nur auf originaler Hardware erlaubt. | /!\ The usage of MikroKopter Software is only permitted on original MikroKopter hardware. |
| Zeile 168: | Zeile 197: |
| * a AtMega1284 Prozessor with programmed bootloader is available [[https://www.mikrocontroller.com/index.php?main_page=product_info&cPath=68&products_id=513|here]] |
Page in 
Page en siehe auch: FlightCtrl_ME_2_0
Inhaltsverzeichnis
Flight Ctrl V2.1
Top Side
Molex-Connector to connect to power distribution board
1 - Molex Connector
Connections from top to bottom:
1 - +12V
2 - I2C Bus (C)
3 - I2C Bus (D)
4 - + Buzzer
5 -Ground (GND FC and Buzzer)
If you are using this new connection you will be unable to install a power switch for your Flight Controller. The Mikrokopter will then get turned on by connecting your Lipo battery. (All MK with more than 4 engines do that anyways).
Bottom Side
1 - 10pin connector for MK-USB or NaviCtrl connection
2 - Pressure Sensor (cut out of sensor connector points to the right)
3 - 6pin connector for servo 2 and Servo 3
4 - 6pin connector for servo 4 and servo 5
5 - DC/DC voltage regulator 5v Recom for Flight Controller
6 - DC/DC voltage regulator 5v Recom for servos
7 - 6pin connector for NaviCtrl
8 - 6pin connector for servo 1 and switchable J16/J17 connectors
9 - I2C connector (C/D) for BL Controllers
10 - JET (If you are using the Jeti Satellite receiver you will have to bridge these two connectors)
11 - 5pin connector (5V, GND, 3,3V, RX,TX)
Connection for Jeti receiver:
Connect PPM cable to #13, bridge the 2 connectors on #10 and connect RX
Connection for Spektrum Satellite::
Connect the orange Receiver cable on 3,3V, black to G and gray to RX
12 - connection for the buzzer (BUZ-/BUZ+)
13 - Connection for PPM receiver (GN-brown, +5V-red, PPM-orange)
14 - Ground (GND) connection for the Flight Controller
15 - Positive (+) connection for the Flight Controller (if a power switch is being used)
16 - Positive (+) connection for the Flight Controller (without a power switch)
Mounting the plug connector, pressure sensor, elko
The FlightCtrl still has to be equipped with some components
![/!\](/moin_static199/mk-style3/img/alert.png "/!\"){kind=small}
The FCV2.1 can with a 5-pin. Molex cables are connected to the power distributor.
When using the Molexkabel between FlightCtrl and powerboard, you don't have to solder the I2C bus, the buzzer and the power cable to the FlightCtrl.
Only the power cable for the receiver still has to be soldered to the FlightCtrl.
The buzzer is connected directly to the appropriate solder points of the flow distributor (Buzzer / -).
The I2C-bus and the voltage supply are provided from the power distribution over the Molex.
Alternatively, the FC V2.1 can be connected with individual cable to the power distributor.
Connections
(FC2.1 and FC2.0 are identical except the new Molex Connector)
Connectors SV2
Upper Row (switchable outputs)
Pin1: 100mA switchable output with NON Open Collector for LED's, Programmable with MK Koptertool with J16.
Pin3: +5 Volt
Pin5: 100mA switchable output with NON Open Collector for LED's, Programmable with MK Koptertool with J17.
Lower row: Nick-Servo Output
Pin2: Servo 1 output (for Nick-Servo camera stabilization)(adjustable via MK Koptertool)
Pin4: +5V (only applicable if you installed a Recom on IC3)
Pin6: GND
Attention: the servo outputs get activated after the calibration of the gyros. Push the throttle lever in the upper left corner until you hear the buzzer and the green LED turns off.
Connectors SV3
Upper row: Servo 3
Pin1: Servo 3 output
Pin3: +5V (only applicable if you installed a Recom on IC3)
Pin5: GND
Lower Row: Roll-Servo Output
Pin2: Servo 2 Output (Setting in Koptertool)
Pin4: +5V (only applicable if you installed a Recom on IC3)
Pin6: GND
Connectors SV4
Upper row: Servo 5
Pin1: Servo 5 output
Pin3: +5V (only applicable if you installed a Recom on IC3)
Pin5: GND
Lower Row: Servo 4
Pin2: Servo 4 output
Pin4: +5V (only applicable if you installed a Recom on IC3)
Pin6: GND
Receiver Connection
Standard PPM-Receiver
Examples:
Connection:
- black to "GN" (negative)
- orange to "+5V" (positive)
- orange to "PPM" (data connection)
Spektrum Satellite Receiver
The 3,3V power connection for the satellite receiver is on the bottom side of the Flight Controller.
Connection:
- black to "g" (negative)
- orange to "3,3V" (positive)
- gray to "Rx" (data connection)
- do not bridge the 2 JET connectors.
Also see: Spektrum
Jeti Satellite Receiver
The external diode is already integrated into the FC2.1 circuit and therefore will not have to get soldered.
Connection:
- black to "GN" (negative)
- orange to "+5V" (positive)
- orange to "PPM" (data connection)
- bridge the 2 connectors for JET
- separate data connection for down-link data gets connected via "RX" to "D" or the receiver
Also see: JetiDuplex
Wiring Diagram
The usage of MikroKopter Software is only permitted on original MikroKopter hardware.
Hardware Changes since V2.00
- new controller with double the flash memory (ATMEGA1284P)
- Molex-connector for easy power distribution board connection
- integrated power supply for Spektrum Satellite receiver
- JET connector bridge for easy usage for JETI down-link
- Adjustable resistor for pressure sensor to accommodate 2000-3000 meters in elevation depending on weather
- resistor adjustment for I2C Pull-Ups.
- Protection diode for Buzzer
- new black color
What's included and what has changed compared with V2.0
- Pressure Sensor MPX4115A is included
- 2 power regulators (recom or similar) are included to supply your flight controller and servos with power
- power switch is NOT includes and has to get ordered separately
Other
- the boot loader for FC2.1 is not public domain and can not be read out thanks to our good friends in china.
a AtMega1284 Prozessor with programmed bootloader is available here
- under no circumstances is it allowed to program or delete the ISP with Atmel programmers