#acl AdminGroup:read,write,revert EditorsGroup:read,write,revert All:read

||<class="MK_TableNoBorder">This page as an '''PDF-Document'''? Click on that Symbol and wait a little moment... ---> ||<class="MK_TableNoBorder"><<PDFIcon>>||<class="MK_TableNoBorder" width= 218px )> [[CalibrateAltitude|{{attachment:symbols/Flagge_EN.jpg}}]]||

{{{#!wiki MK_Nav
||<class="MK_Nav_Header">'''Calibrate barometric altitude sensor'''||
}}}

<<BR>>

##############################################################################
##############################################################################

##----------------------------------------------------------------------------
## Bild rechts Artikel

{{{#!html
<div style="float: right; margin: 15px;">
}}}
{{ http://gallery3.mikrokopter.de/var/albums/intern/sonstiges/Button-Baugruppe/Button350x150/Button_CaliAltitude.jpg?m=1485874367 }}
{{{#!html
</div>
}}}
##----------------------------------------------------------------------------

##############################################################################
##############################################################################


<<BR>>
<<TableOfContents>>
<<BR>><<BR>>


##############################################################################
##############################################################################


##Einfügen_Start 


= Calibrate barometric altitude sensor =

##include_Altitude_begin

~-!!! The following settings apply '''only''' to '''!FlightCtrl V3.0''' - Older !FlightCtrl versions can __not__ be calibrated !!!-~
<<BR>><<BR>><<BR>>

The barometric height sensor is required for automatic holding of the height of the !MikroKopter. <<BR>>
The sensor should be calibrated once. Thus, the sensor is working properly even under temperature fluctuations ~-(factor = x cm per °C)-~.

If the sensor is not calibrated, the copter can vary in height. <<BR>>

Recalibration of the height sensor is not usually necessary. <<BR>><<BR>>

'''INFO:''' Before the [[en/FlightCtrl_V3.0|FlightCtrl]] was delivered, the altitude sensor has already been calibrated.


<<BR>><<BR>><<BR>><<BR>>

== Calibration ==

{{{{#!wiki important

For calibration of the barometric height sensor, a heat source is required. <<BR>>
This can be e.g. a lamp or a hair dryer.

'''IMPORTANT: The heating MUST be SLOW.'''

}}}}

<<BR>><<BR>>

~+'''__The calibration is done in a few steps:__'''+~ <<BR>><<BR>>


||<class="MK_THeader" width= 650px>Step||<class="MK_THeader" width= 400px>Example view||
||'''Step 1'''<<BR>><<BR>>The heat source (switched off) is positioned over the FlightCtrl.<<BR>>(~-You can remove the GPS if you want - then heating is a little faster.)-~||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-LampeAUS.jpg?m=1485942778 }}||
||'''Step 2'''<<BR>><<BR>>Connect the copter now with your computer.<<BR>>~-(via MK-USB or wireless)-~<<BR>><<BR>>Start the !KopterTool and power up the copter.<<BR>>~-(also switch on the transmitter)-~||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/Copter-PC.jpg?m=1485942779 }}||
||'''Step 3'''<<BR>><<BR>>Click the button "!NaviCtrl" in the !KopterTool.<<BR>>In the virtual window press the red arrow (left or right) and change the view to "Barometer". ||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-Step1.jpg?m=1485944116 }}||
||'''Step 4'''<<BR>><<BR>>When you see "Barometer" press the red arrow (up) under "(CAL)" and start the calibration.||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-Step2.jpg?m=1485944117 }}||
||'''Step 5'''<<BR>><<BR>>Now switch on the heat source.||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-LampeAN.jpg?m=1485942778 }}||
||The virtual display shows now "Warm up slowly" and the temperature increases slowly.||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-Step3.jpg?m=1485944117 }}||
||If this is to fast (it is to hott) you see the error "Heater off!"<<BR>><<BR>>Remove then the heat source and wait until the error is gone.<<BR>>If all is OK replace the heat source again with more space.||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-Step4.jpg?m=1485944118 }}||
||'''Step 6'''<<BR>><<BR>>If the heating is carried out correctly, an "Okay" appears after some time. in the lower right corner you see also a "save".<<BR>><<BR>>To save the calibration press the red arrow (up) under save.||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-Step5.jpg?m=1485944118 }}||
||The calibration is complete.||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-Step6.jpg?m=1485944119 }}||



<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>


= Check calibration / manual adjustment =

In the window "Temperature settings" you can check the stored value and also change it.
<<BR>><<BR>>
~-!! If you change the value manually you can also have a negative effect during altitude hold - better use the automatic calibration!!!-~
<<BR>><<BR>>
||<class="MK_THeader" width= 650px>Step||<class="MK_THeader" width= 400px>Example view||
||Beside the button "Settings" you find a smal arrow down. With this arrow you can open the window "Temperature settings".||<:>{{ http://gallery3.mikrokopter.de/var/thumbs/intern/AltitudeCalibration/CalibrateAltitude-manual.jpg?m=1485878339 }}||

##include_Altitude_end

##Einfügen_Ende

<<BR>><<BR>><<BR>><<BR>><<BR>><<BR>>