Diese Seite dient zum Einfügen in andere Seiten per Include-Macro. So wird redundanter Inhalt vermieden.

Syntax: <<Include(include/assembling/rigger-Motor-XL2, , from="^-----$", to="^-----$")>>
---> fügt diese Seite in Deutsch zwischen den Horizontalen-Trennern ein.

This page is used to insert into other pages via include macro. Thus, avoid redundant content.

Syntax: <<Include(include/assembling/rigger-Motor-XL2, , from="^------$", to="^------$")>>
---> add this page into English between horizontal separators.

Cette page est utilisée pour être insérée dans d'autres via une macro d'insertion. Ceci évitera le contenu redondant.

Syntax: <<Include(include/KopterTool/rigger-Motor-XL2, , from="^-------$", to="^-------$")>>
---> Ajoute la partie française de cette page contenue entre les bandeaux horizontaux.




Deutsch Start



Ausleger

Montage der Motoren

{i} Dieser Schritt ist nur noch beim MK Basisset Okto XL Blue erforderlich - In den allen anderen OktoXL Sets befinden sich Ausleger bei denen die Motoren bereits vormontiert sind.

{i} Bevor die drei Motor-Leitungen in jeden Ausleger eingezogen werden, sollte der Motor angeschraubt werden.

Die Motoren werden mit den beiliegenden Schrauben und Winkeladapter montiert. Damit sich die Schrauben nicht während des Fluges lösen, sollten diese auf jeden Fall mit etwas Schraubensicherungslack (Loctite mittelfest o.a.) montiert werden. Es reicht ein kleiner Tropfen Sicherungslack hierfür aus!

/!\ ACHTUNG: Die Schrauben sollen fest angeschraubt werden. Allerdings können die Gewinde in den Motoren bei zu viel Kraft überdreht werden!

{i} Die Gewinde am Motor (oben/unten links/rechts) haben unterschiedliche Abstände!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html



{i} Zum besseren Gieren werden die Winkeladapter an jedem Motor verbaut. Diese 3° Winkeladapter Platten werden zwischen dem Motor und dem Ausleger montiert.
Die bei den Winkeladapter beiliegenden Montageschrauben werden hierbei durch den Ausleger und den Winkeladapter in den Motor geschraubt.
Wichtig ist, das die Adapter bei einem links drehenden Motor mit der abgeschrägten Seite nach links montiert wird. Bei einem rechts drehenden Motor schaut die abgeschrägten Seite nach rechts.

Links drehender Motor

Rechts drehender Motor

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82222&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php/v/tech/MotorAngle_Left_Rotating.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/IMG_4622.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Links.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Rechts.jpg.html

Okto(XL):
alle kurzen Ausleger (2,4,6,8)

Okto(XL):
alle langen Ausleger (1,3,5,7)



Nähere Infos, auch zur Montage findet man hier: Winkeladapter

Motor-, LED-Kabel einziehen.

Zusätzlich zu den Motorleitungen werden in die Ausleger, an denen eine Beleuchtung zusätzlich montiert wird, jeweils eine rote und eine schwarze 0,5mm²-Silikonleitung in passender Länge eingezogen.
Beim Einziehen der Leitungen sollte darauf geachtet werden, dass die Leitungen nicht beschädigt werden.

Die Leitungen für den Motor und die Beleuchtung werden durch die Kabeleinführungen an der Unterseite des Auslegers eingezogen.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ Die Kabel werden auf der linken Seite der Ausleger (ovales Loch) wieder herausgeführt! (Vom Mittelpunkt der Centerplate aus gesehen.)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html

Beispielbild

{i} Tipps:

  • Die Leitungen vor dem Durchziehen am Ende zusammenkleben oder löten.
  • Ggf. eine einzelne Leitung oder einen Faden zuerst durchziehen, an der man die drei bzw. fünf befestigt. Dann mit dieser Leitung die anderen durchziehen.

/!\ Achtung: Dreht man die Motoren von Hand mit zusammen gelöteten Anschlüssen, bemerkt man evtl., dass sie schwergängig sind. Dies liegt am kurzgeschlossenen induzierten Strom !

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propellermitnehmer montieren

Die drei Schrauben der Propellermitnehmer sollten fest angezogen werden. Hierbei sollte ein passender Schraubendreher genutzt werden um die Schraubköpfe nicht zu beschädigen!
Auf dem Propellermitnehmer wird später der Propeller befestigt. Wie die Montage durchzuführen ist, wird Beispielhaft an den Bildern deutlich.

Beispiel: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html



Deutsch Stop





Englisch Start



Rigger

Mounting the Motor

{i} This step is only necessary in the MK Basisset Okto XL Blue - In all other OktoXL sets there are riggers with already mounted motors.

{i} Mount the motor first bevor insertoing the cables.

The motors and the angle adapter are mounted with two screws. To avoid loosing the motors, use a little drop of Threadlocker.

/!\ ATTENTION: The screws should be screwed firmly. If the screws are screwed too tightly, the threads can be destroyed!

{i} The threads on the motor (above/below left/right) have different distances!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html



/!\ For a better yaw function you can install on each motor a angle adapter. This 3° angle adapter plates are fitted between the engine and the rigger.
The included mounting screws are screwed through the rigger and adapter.
It is important that the adapter is mounted in a left-turning engine with the beveled side to the left. In a right rotating motor, the beveled side looks to the right.

left turning Motor

right turning Motor

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82222&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php/v/tech/MotorAngle_Left_Rotating.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/IMG_4622.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Links.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Rechts.jpg.html

Okto(XL):
all short rigger (2,4,6,8)

Okto(XL):
all long rigger (1,3,5,7)



More information, including the installation can be found here: angle adapter

install the motor-, LED-cables

Also mount the red and one black 0,5mm cable (in suitable length) into the riggers wich obtain a LED-stripe or a buzzer.
Please be carefull while installing the cables.

Insert the cable like you see below.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ The cable of the Motor comes out of the hole on the left side of the rigger! (see picture)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html
Example picture

{i} Tips:

  • Stick or solder wires together before pulling them through the hole.
  • if needed, attatch a string to the wires and pull that through first.

/!\ Attention: If you connect the motorcables, it is difficult to turn the motor!

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propeller Mount

The three screws of the propeller mount should be firmly screwed. In this case use a suitable screwdriver!
Later you can mount the propeller like the picture show.

Example: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html



Englisch Stop





French Start



Rigger

Mounting the Motor

{i} Mount the motor first bevor insertoing the cables.

The motors and the angle adapter are mounted with two screws. To avoid loosing the motors, use a little drop of Threadlocker.

/!\ ATTENTION: The screws should be screwed firmly. If the screws are screwed too tightly, the threads can be destroyed!

{i} The threads on the motor (above/below left/right) have different distances!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html



/!\ For a better yaw function you can install on each motor a angle adapter. This 3° angle adapter plates are fitted between the engine and the rigger.
The included mounting screws are screwed through the rigger and adapter.
It is important that the adapter is mounted in a left-turning engine with the beveled side to the left. In a right rotating motor, the beveled side looks to the right.

left turning Motor

right turning Motor

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82222&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php/v/tech/MotorAngle_Left_Rotating.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/IMG_4622.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Links.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Rechts.jpg.html

Okto(XL):
all short rigger (2,4,6,8)

Okto(XL):
all long rigger (1,3,5,7)



More information, including the installation can be found here: angle adapter

install the motor-, LED-cables

Also mount the red and one black 0,5mm cable (in suitable length) into the riggers wich obtain a LED-stripe or a buzzer.
Please be carefull while installing the cables.

Insert the cable like you see below.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ The cable of the Motor comes out of the hole on the left side of the rigger! (see picture)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html
Example picture

{i} Tips:

  • Stick or solder wires together before pulling them through the hole.
  • if needed, attatch a string to the wires and pull that through first.

/!\ Attention: If you connect the motorcables, it is difficult to turn the motor!

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propeller Mount

The three screws of the propeller mount should be firmly screwed. In this case use a suitable screwdriver!
Later you can mount the propeller like the picture show.

Example: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html



French Stop


  • KategorieInclude/assembling

Diese Seite dient zum Einfügen in andere Seiten per Include-Macro. So wird redundanter Inhalt vermieden.

Syntax: <<Include(include/assembling/rigger-Motor-XL2, , from="^-----$", to="^-----$")>>
---> fügt diese Seite in Deutsch zwischen den Horizontalen-Trennern ein.

This page is used to insert into other pages via include macro. Thus, avoid redundant content.

Syntax: <<Include(include/assembling/rigger-Motor-XL2, , from="^------$", to="^------$")>>
---> add this page into English between horizontal separators.

Cette page est utilisée pour être insérée dans d'autres via une macro d'insertion. Ceci évitera le contenu redondant.

Syntax: <<Include(include/KopterTool/rigger-Motor-XL2, , from="^-------$", to="^-------$")>>
---> Ajoute la partie française de cette page contenue entre les bandeaux horizontaux.




Deutsch Start



Ausleger

Montage der Motoren

{i} Bevor die drei Motor-Leitungen in jeden Ausleger eingezogen werden, sollte der Motor angeschraubt werden.

Die Motoren werden mit den beiliegenden Schrauben und Winkeladapter montiert. Damit sich die Schrauben nicht während des Fluges lösen, sollten diese auf jeden Fall mit etwas Schraubensicherungslack (Loctite mittelfest o.a.) montiert werden. Es reicht ein kleiner Tropfen Sicherungslack hierfür aus!

/!\ ACHTUNG: Die Schrauben sollen fest angeschraubt werden. Allerdings können die Gewinde in den Motoren bei zu viel Kraft überdreht werden!

{i} Die Gewinde am Motor (oben/unten links/rechts) haben unterschiedliche Abstände!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html



{i} Zum besseren Gieren werden die Winkeladapter an jedem Motor verbaut. Diese 3° Winkeladapter Platten werden zwischen dem Motor und dem Ausleger montiert.
Die bei den Winkeladapter beiliegenden Montageschrauben werden hierbei durch den Ausleger und den Winkeladapter in den Motor geschraubt.
Wichtig ist, das die Adapter bei einem links drehenden Motor mit der abgeschrägten Seite nach links montiert wird. Bei einem rechts drehenden Motor schaut die abgeschrägten Seite nach rechts.

Links drehender Motor

Rechts drehender Motor

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82222&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php/v/tech/MotorAngle_Left_Rotating.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/IMG_4622.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Links.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Rechts.jpg.html

Okto(XL):
alle kurzen Ausleger (2,4,6,8)

Okto(XL):
alle langen Ausleger (1,3,5,7)



Nähere Infos, auch zur Montage findet man hier: Winkeladapter

Motor-, LED-Kabel einziehen.

Zusätzlich zu den Motorleitungen werden in die Ausleger, an denen eine Beleuchtung zusätzlich montiert wird, jeweils eine rote und eine schwarze 0,5mm²-Silikonleitung in passender Länge eingezogen.
Beim Einziehen der Leitungen sollte darauf geachtet werden, dass die Leitungen nicht beschädigt werden.

Die Leitungen für den Motor und die Beleuchtung werden durch die Kabeleinführungen an der Unterseite des Auslegers eingezogen.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ Die Kabel werden auf der linken Seite der Ausleger (ovales Loch) wieder herausgeführt! (Vom Mittelpunkt der Centerplate aus gesehen.)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html

Beispielbild

{i} Tipps:

  • Die Leitungen vor dem Durchziehen am Ende zusammenkleben oder löten.
  • Ggf. eine einzelne Leitung oder einen Faden zuerst durchziehen, an der man die drei bzw. fünf befestigt. Dann mit dieser Leitung die anderen durchziehen.

/!\ Achtung: Dreht man die Motoren von Hand mit zusammen gelöteten Anschlüssen, bemerkt man evtl., dass sie schwergängig sind. Dies liegt am kurzgeschlossenen induzierten Strom !

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propellermitnehmer montieren

Die drei Schrauben der Propellermitnehmer sollten fest angezogen werden. Hierbei sollte ein passender Schraubendreher genutzt werden um die Schraubköpfe nicht zu beschädigen!
Auf dem Propellermitnehmer wird später der Propeller befestigt. Wie die Montage durchzuführen ist, wird Beispielhaft an den Bildern deutlich.

Beispiel: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html



Deutsch Stop





Englisch Start



Rigger

Mounting the Motor

{i} Mount the motor first bevor insertoing the cables.

The motors and the angle adapter are mounted with two screws. To avoid loosing the motors, use a little drop of Threadlocker.

/!\ ATTENTION: The screws should be screwed firmly. If the screws are screwed too tightly, the threads can be destroyed!

{i} The threads on the motor (above/below left/right) have different distances!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html



/!\ For a better yaw function you can install on each motor a angle adapter. This 3° angle adapter plates are fitted between the engine and the rigger.
The included mounting screws are screwed through the rigger and adapter.
It is important that the adapter is mounted in a left-turning engine with the beveled side to the left. In a right rotating motor, the beveled side looks to the right.

left turning Motor

right turning Motor

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82222&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php/v/tech/MotorAngle_Left_Rotating.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/IMG_4622.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Links.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Rechts.jpg.html

Okto(XL):
all short rigger (2,4,6,8)

Okto(XL):
all long rigger (1,3,5,7)



More information, including the installation can be found here: angle adapter

install the motor-, LED-cables

Also mount the red and one black 0,5mm cable (in suitable length) into the riggers wich obtain a LED-stripe or a buzzer.
Please be carefull while installing the cables.

Insert the cable like you see below.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ The cable of the Motor comes out of the hole on the left side of the rigger! (see picture)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html
Example picture

{i} Tips:

  • Stick or solder wires together before pulling them through the hole.
  • if needed, attatch a string to the wires and pull that through first.

/!\ Attention: If you connect the motorcables, it is difficult to turn the motor!

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propeller Mount

The three screws of the propeller mount should be firmly screwed. In this case use a suitable screwdriver!
Later you can mount the propeller like the picture show.

Example: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html



Englisch Stop





French Start



Rigger

Mounting the Motor

{i} Mount the motor first bevor insertoing the cables.

The motors and the angle adapter are mounted with two screws. To avoid loosing the motors, use a little drop of Threadlocker.

/!\ ATTENTION: The screws should be screwed firmly. If the screws are screwed too tightly, the threads can be destroyed!

{i} The threads on the motor (above/below left/right) have different distances!

http://gallery.mikrokopter.de/main.php/v/tech/MK3538d.jpg.html



/!\ For a better yaw function you can install on each motor a angle adapter. This 3° angle adapter plates are fitted between the engine and the rigger.
The included mounting screws are screwed through the rigger and adapter.
It is important that the adapter is mounted in a left-turning engine with the beveled side to the left. In a right rotating motor, the beveled side looks to the right.

left turning Motor

right turning Motor

https://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82222&g2_serialNumber=2

http://gallery.mikrokopter.de/main.php/v/tech/MotorAngle_Left_Rotating.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/IMG_4622.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Links.jpg.html

http://gallery.mikrokopter.de/main.php/v/tech/Drehrichtung-Rechts.jpg.html

Okto(XL):
all short rigger (2,4,6,8)

Okto(XL):
all long rigger (1,3,5,7)



More information, including the installation can be found here: angle adapter

install the motor-, LED-cables

Also mount the red and one black 0,5mm cable (in suitable length) into the riggers wich obtain a LED-stripe or a buzzer.
Please be carefull while installing the cables.

Insert the cable like you see below.

http://gallery.mikrokopter.de/main.php/v/tech/Ausleger_001.jpg.html

/!\ The cable of the Motor comes out of the hole on the left side of the rigger! (see picture)

http://gallery.mikrokopter.de/main.php/v/tech/IMG_6380.JPG.html
Example picture

{i} Tips:

  • Stick or solder wires together before pulling them through the hole.
  • if needed, attatch a string to the wires and pull that through first.

/!\ Attention: If you connect the motorcables, it is difficult to turn the motor!

http://gallery.mikrokopter.de/main.php/v/tech/Kabel_52cm.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/Kabeldurchziehenvorbereiten2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen2.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen3.JPG.html http://gallery.mikrokopter.de/main.php/v/tech/Motorauslegerschwarzkabel_summerledkabeldurchziehen8.JPG.html

Propeller Mount

The three screws of the propeller mount should be firmly screwed. In this case use a suitable screwdriver!
Later you can mount the propeller like the picture show.

Example: MK3538 Motor
http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-1.jpg.html http://gallery.mikrokopter.de/main.php/v/tech/MK3538-PropHalter-2.jpg.html



French Stop


  • KategorieInclude/assembling