#acl AdminGroup:read,write,revert EditorsGroup:read,write,revert All:read ||This page as an '''PDF-Document'''? Click on that Symbol and wait a little moment... ---> ||<>|| {{{#!wiki MK_Nav ||'''LANC-Ctrl V1.1 + Multi Adapter'''|| }}} {{{#!wiki MK_select1 * {{http://mikrokopter.de/images/deu.gif}} [[LancCtrl_V1.1-Multi|deutsch]] }}} <
> See also: [[en/LancCtrl|LANC-Ctrl]] <
><
> <> = LANC-Ctrl Version 1.1 + Multi Adapter = '''Shoplink: '''[[https://www.mikrocontroller.com/index.php?main_page=product_info&cPath=112&products_id=797&zenid=c1cd02d9f7bfb16c35f119f9e8763478|LANC-Ctrl V1.1 + Multi Adapter]] <
><
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=140960&g2_serialNumber=2}} {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131002&g2_serialNumber=2}} <
><
> It is a control board incl. video output to operate cameras with a LANC interface (i.e. Sony PJ780/PJ650/CX410)<
> The LANC-Ctrl can be connected either way to the !FlightCtrl or to two PPM outputs of a receiver.<
> Via the LANC protocol, functions like triggering photos, starting video shots and the zoom (with variable speed), can be controlled.<
> To start the recording the switch on the remote is switched permanently to REC. That makes the start recording way safer as with the REC-Start/Stop button of the infra-red remote. <
><
> == Innovations == Compared to the previous version [[en/LancCtrl|LANC-Ctrl V1.0]] the new version is considerably smaller, easier and more flexible.<
> An additional Y-cable for the video- and LANC connection is no longer necessary. The LANC cable is now directly connected to the electronic.<
> You can take now the video signal from the video transmitter or directly via an adapter from the LANC-Ctrl.<
> A new and advanced software makes the use of the alternative software unnecessary. In that way, i.e. the Sony CX730 and also the Sony HDR-CX350VE, can be used without any changes. == Video == <> == Functions == Following functions can be operated: * Zoom-in & out (variable speed from very slow up to very fast) * REC Start/Stop * trigger photo (both, in photo mode as well as in video mode) <
> The zoom function can be used via a potentiometer / slider or a 3-way switch on the transmitter.<
> Via a potentiometer / slider the zoom speed can be controlled infinitely. With a 3-way switch is no control of the zoom speed possible. <
> The functions are as follows: <
> * Middle position of the 3-way switch or potentiometer / slider = Zoom STOP * Switch or potentiometer / slider down = Zoom OUT * Switch or potentiometer / slider up = Zoom IN <
> To trigger photos and start recording, this is possible with the 3-way switch. <
> The functions are as follows: <
> * Switch down (-127) = Function OFF (Recording STOP) * Switch in middle position (0) = Triggering the video camera (Please read the instructions of the video camera. Not usually possible with HD recording) * Switch up (+127) = Recording START == Technical Data == * Supply voltage max. 6V= * Weight: approx.14g with cables * Dimension of the PCB: approx. 30x17,5mm * Cable length: SONY LANC approx. 12cm * Cable length: Servo cable apprx. 23cm <
><
> {{{#!wiki caution '''IMPORTANT - Please read!''' The LANC-Ctrl has two inputs - PPM1 + PPM2. <
><
> Connect always both inputs (PPM1+PPM2) either directly to the !FlightCtrl '''OR''' to the receiver.<
><
> The supply voltage of max. 6V for the LANC-Ctrl comes via the 3-wire PPM cable.<
> }}} ######################################################################################################################################################################### = Inputs/Outputs = The LANC-Ctrl has two PPM inputs (PPM1 + PPM2). <
><
> * PPM1 = Supply voltage LANC-Ctrl + Zoom in / Zoom out * PPM2 = REC on/off + trigger photo <
><
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=140966&g2_serialNumber=2}} <
><
> ######################################################################################################################################################################### = Connection = The LANC-Ctrl can be connected via the servo outputs of the !FlightCtrl or via a conventional receiver with servo outputs.<
><
> == Connection servo output FlightCtrl == The LANC-Ctrl can be connected to the servo outputs "Servo3" and "Servo4" [[en/FlightCtrl_ME_2_1|(Link)]] of the !FlightCtrl.<
><
> [[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130369&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130372&g2_serialNumber=2}}]] <
> (To enlarge -> click on the image) <
><
> == Connection to the receiver == The LANC-Ctrl can be also connected directly to the receiver.<
><
> [[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130375&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130378&g2_serialNumber=2}}]] <
> (To enlarge -> click on the image) <
><
> == Connection camera + video transmitter == The connection to the video camera comes via the LANC plug. <
> If the video transmitter AV NANO Stinger is used [[https://www.mikrocontroller.com/index.php?main_page=product_info&cPath=112&products_id=679|(Link)]], it can be connected directly to the LANC-Ctrl . <
><
> [[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=140969&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=140972&g2_serialNumber=2}}]] <
> (To enlarge -> click on the image) <
><
> If a different video transmitter is used without an appropriate plug, an adapter can be used: <
><
> [[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130393&g2_serialNumber=2|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130396&g2_serialNumber=4}}]] <
> (To enlarge -> click on the image) <
><
> ######################################################################################################################################################################### = Settings = If the LANC-Ctrl is connected directly to the FlightCtrl or only to a receiver, some smaller adjustments of the settings need to be done.<
><
> In this example we take: * Channel 7 for the function ''Zoom'' and * Channel 11 to trigger as well as start/stopp the recording. <
><
> == Settings FlightCtrl == '''Step 1''' <
> PPM1+PPM2 of the LANC-Ctrl should be connected to ''Servo3'' and ''Servo4'' of the !FlightCtrl.<
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130372&g2_serialNumber=2}} <
><
><
> '''Step 2''' <
> At the transmitter a potentiometer or a slider is assigned to channel 7 and a 3-way switch to channel 11.<
> (The assignment of channels to a switch, button or potentiometer can be read in the instruction manual of the transmitter)<
><
> Via the tab ''Channels'' in the settings of the KopterTool the assignment / function can be checked.<
><
> Channel 11 - assigned to a 3-way switch: <
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131022&g2_serialNumber=2}}<
><
><
> Channel 7 - assigned to a potentiometer or slider: <
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131010&g2_serialNumber=2}}....... {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131016&g2_serialNumber=2}} <
><
><
> '''Step 3''' <
> In the settings of the KopterTool channel 7 (Poti3) and 11 (Poti7) will be assigned to the servo outputs ''Servo3'' and ''Servo4''.<
><
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130417&g2_serialNumber=1}} <
><
> '''INFO:''' The channels 5-12 in the settings are referred as ''Poti 1-8'' ([[MK-Parameter/Channels|Link]]). <
><
><
> '''Done.''' <
><
> After the calibration of the gyros (Throttle up + Yaw left) the servo outputs of the FlightCtrl are active and can be controlled via the transmitter. <
><
><
><
> == Settings receiver == The LANC-Ctrl can also be operated directly via a receiver. <
> This example shows: * Channel 7 for the function ''Zoom'' and * Channel 11 to trigger as well as start/stop the recording. '''Step 1''' <
> PPM1+PPM2 of the LANC-Ctrl will be connected to the receiver.<
> PPM1 is connected to the servo output 7, PPM2 to servo output 11. <
> (Receiver with appropriate servo outputs required.) <
><
><
> '''Step 2''' <
> At the transmitter a potentiometer or a slider is assigned to channel 7 and a 3-way switch to channel 11.<
> (The assignment of channels to a switch, button or potentiometer can be read in the instruction manual of the transmitter)<
><
> Channel 11 - assigned to a 3-way switch: <
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131059&g2_serialNumber=1}}<
><
><
> Channel 7 - assigned to a potentiometer or slider: <
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131054&g2_serialNumber=1}}<
><
><
> '''Done.''' <
><
><
><
> If there is no receiver with 12 or more servo outputs available, a Graupner HoTT receiver with less servo outputs can be used.<
> To each Graupner HoTT receiver (GR-12 / GR-16 / GR-24) new channels can be assigned to the servo outputs.<
><
> For this example we take a Graupner HoTT receiver ''GR-16'' with 8 servo outputs. <
> Here should be: * '''Channel 7''' (function ''Zoom'') at '''servo output 2''' and * '''Channel 11''' (trigger + start/stopp the recording) at '''servo output 1'''. {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=130378&g2_serialNumber=2}} On the Graupner HoTT transmitter switch to the menue '''base setup model'''. There you choose ''Rcv Ch Map'' (E08) with the button '''SET''' . <
><
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131083&g2_serialNumber=2}} <
><
> In the window which opens up choose the first servo output ''Rx Output Ch 1'' and set the ''Rx Input Ch 1'' to channel 11.<
> At ''Rx Output Ch 2''set the ''Rx Input Ch 2'' to channel 7.<
><
> {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131090&g2_serialNumber=2}} {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=131097&g2_serialNumber=2}} ######################################################################################################################################################################### = Modifikation for Blackmagic camera = [[http://gallery.mikrokopter.de/main.php/v/tech/LANC_Blackmagic1.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=146384}}]] * Rec on/off can be controlled * Zoom ist not supported by this camera * The PPM-Cable for Zoom is not needed. If you want to remove it, connect the orange line of the PMM-Cable to "PPM2" (see below) * Use a 2-stage switch of your transmitter * Attach a 2,5mm connector like this: [[http://gallery.mikrokopter.de/main.php/v/tech/LANC_Blackmagic_Mod.jpg.html|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=146380}}]] ######################################################################################################################################################################## = Tested Cameras = * Sony HDR-CX350VE * Sony HDR-CX410 * Sony HDR-CX730 * Sony HDR-CX760 * Sony HDR-PJ650 * Sony HDR-PJ740 * Sony HDR-PJ780 * Sony HDR-PJ810 This cameras will not work: * Sony HDR-PJ530E * Sony HDR-PJ620 * SOny FDR-AX33B ######################################################################################################################################################################### = LANC-Ctrl V1.0 = Here you can find information about the previous version LANC-Ctrl V1.0: [[en/LancCtrl|Link]] ---- KategorieMK-Baugruppe/de