#acl AdminGroup:read,write,revert All:read

{{{#!wiki MK_Nav
||||||<class="MK_Nav_Header">Step 11 - Outputs||
||<class="MK_Nav_left">[[en/Erstinbetriebnahme/Step10|{{attachment:symbols/Pfeil_links.png}}]]Wikiseite zurück||<class="MK_Nav_middle">[[en/Erstinbetriebnahme/Help|{{attachment:symbols/Help.png}}]]||<class="MK_Nav_right">Wikiseite vor [[en/Erstinbetriebnahme/Step12|{{attachment:symbols/Pfeil_rechts.png}}]]||
}}}

{{{#!wiki MK_select1

 * {{http://mikrokopter.de/images/deu.gif}} [[Erstinbetriebnahme/Step11|deutsch]]
 * {{http://mikrokopter.de/images/fra.gif}} [[fr/Erstinbetriebnahme/Step11|français]]
}}}


##include_step_begin

= Step 11 - Outputs =
== Requirement ==
 * '''Step10''' has been read.

<!> Who has got no !ShutterCable assembled to trigger the camera or an ExtensionPCB to switch the lighting on the Kopter can skip this point and continue with the next '''"Step"'''.<<BR>><<BR>>

== ExtensionPCB oder ShutterCable ==
If already an [[en/ExtensionPCB|ExtensionPCB]] to control the lighting or a [[en/ShutterCable|ShutterCable]] to trigger the camera has been mounted to the Kopter<<BR>>
the connection should be look in that way: <<BR>><<BR>>

||<class="MK_THeader">[[en/ExtensionPCB|ExtensionPCB]]||||<class="MK_THeader">[[en/ShutterCable|ShutterCable]] at output 1 or 2||
||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97123&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108234&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97165&g2_serialNumber=1|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=99755&g2_serialNumber=2}}]]||[[http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97128&g2_serialNumber=3|{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=99754&g2_serialNumber=2}}]]||

== Setting Outputs ==
The FlightCtrl has got two switch outputs. These outputs can be independently switched and set.<<BR>>
You can let flash the LEDs or you can switch them ON/OFF. Also you can use an output to trigger a camera. <<BR>><<BR>>

{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=90885&g2_serialNumber=2}}<<BR>><<BR>>

The both switching outputs you can find on the __upper__ pin header '''SV2''' on the !FlightCtrl: <<BR>><<BR>>

{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=82439&g2_serialNumber=2}}<<BR>><<BR>>

A ground potential will be switched here!<<BR>><<BR>>
 

{{{#!wiki caution
'''__ATTENTION__'''

The lighting should be '''__NOT__''' directly connected to that outputs. The transistors on the !FlightCtrl could be damaged! <<BR>>
To switch the lighting you should use i.e. the [[en/ExtensionPCB|Extension-PCB]]. Over that PCB you can connect the lighting (also with nmore power).<<BR>>
To trigger the camera you can use the Extension-PCB as well as the [[en/ShutterCable|ShutterCable]].<<BR>>
}}}

<<BR>><<BR>><<BR>>


To set up a blink sequence on an output you can choose throughout the 8 boxes in the '''Bit mask''' different flash pattern.<<BR>>
The speed of the blink sequence you can set with a number under '''Timing''': <<BR>><<BR>>

'''Example Output1 (OUT1)''' <<BR>>
{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=99768&g2_serialNumber=1}}<<BR>><<BR>><<BR>><<BR>>



If you want to trigger a camera over an output (i.e.with a ShutterCable) you can set it here also.<<BR>>
You should only activate the first box in the '''Bit mask'''. Under '''Timing''' the channel  (POTI) of the button will be set here at the transmitter: <<BR>><<BR>>


'''Example Output1 (OUT1) Poti 8 => Channel 12''' <<BR>>
{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=99766&g2_serialNumber=1}}<<BR>><<BR>><<BR>><<BR>>


If an output was set to trigger a camera you should disable the '''Low voltage warning''' for that output.<<BR>>
Otherwise with an empty Lipo and the following battery warning the camera would trigger continuously: <<BR>><<BR>>

'''Example Output1 (OUT1) = OFF'''<<BR>>
{{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=99770&g2_serialNumber=1}}<<BR>><<BR>><<BR>><<BR>>


As soon as you save this settings with the button {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=96463&g2_serialNumber=2}} into the !FlightCtrl  the LEDs strat to flash or you can trigger a camera.<<BR>>
(With a connected LED-Lighting the LEDs start blinking with a low voltage warning.)<<BR>><<BR>>

{{{{#!wiki important
'''__INFO__'''

You can use also a switch/channel at your transmitter to switch the LEDs. <<BR>>
Independently of the set flashing pattern you permanently switch the LEDs with the switch '''ON''' or '''OFF'''.<<BR>><<BR>>

 If you can not <<BR>>
 -switch OFF the lighting with a switch/button on your transmitter  <<BR>>
  or
 - not triggering the !ShutterCable <<BR>>
 it is the fact that the servo travel is not set up right at the transmitter! That was explained in the previous step '''"Check channels"'''.
}}}}


<<BR>><<BR>><<BR>>

After these settings you can close the setting window. Here you need to "click" on {{http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=97742&g2_serialNumber=1}}<<BR>>
We are now back to the "Main Window" of the !KopterTool.


##include_step_end


<<BR>><<BR>><<BR>><<BR>>

Everything OK? Then it continues here:
[[en/Erstinbetriebnahme/Step12|{{attachment:symbols/Pfeil_rechts.png}}]]