MikroKopter

This page as an PDF-Document? Click on that Symbol and wait a little moment... --->

Bluetooth-Set


See also: MikroKopter-Boards

Bluetooth-Set

Shoplink: Bluetooth-Set

The Bluetooth-Set V2.0 consists of a Bluetooth-Transmitter and a Bluetooth-Receiver. Both modules are already set and paired which allows a connection without any interference.
The range of the modules are specified by the manufacturer with up to 500mtr. The set contains everything what is necessary to connect it to the Kopter and to the PC.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108948&g2_serialNumber=2

Bluetooth-Set V2.0
1x Bluetooth-Module PC
1x Bluetooth-Module Kopter
1x Connection-cable Bluetooth <-> Kopter
1x USB-cable Bluetooth <-> PC

Connection PC

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108937&g2_serialNumber=2

For the installation of the MK-Bluetooth-USB a VCP-Driver is necessary. This driver can be downloaded here: VCP-Driver
INFO: Using Windows 7 a separated driver is not necessary.

The MK-Bluetooth-USB will be connected via the USB-cable with the PC.
Here now you need to connect the Mini-USB plug of the USB-cable to the MK-Bluetooth-USB and the USB plug to a free port on the PC.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108939&g2_serialNumber=1

After connecting the MK-Bluetooth-USB the blue LED lights on, the module will be automatically detected and for the appropriate driver will be searched online as well as installed.
This procedure can take a few minutes.

In the device manager you can find the COM-Port for the MK-Bluetooth-USB. Here you can see also the COM-Port number which is required later on in the KopterTool.

Connection MikroKopter

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108926&g2_serialNumber=2

The enclosed ribbon cable will be connected with one side to the MK-Bluetooth.
The other side is connected either to the FlightCtrl (EXT1) or when using the GPS-System to the NaviCtrl (Debug).

The plug can be connected here only in the correct polarity to the MK-Bluetooth. Connecting to the FlightCtrl or NaviCtrl you need to take care of a correct connection!
The plug must show with the red side of the ribbon cable to pin "1" of the pin-header.

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108951&g2_serialNumber=1

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108957&g2_serialNumber=1

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108963&g2_serialNumber=1

Connecting to MK-Bluetooth

Connecting to FlightCtrl

Connecting to NaviCtrl



The connection to a Kopter can look in that way:

http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=108929&g2_serialNumber=1

Connection to the KopterTool

Are both Bluetooth-Modules connected you can start the KopterTool. Here now the COM-Port for the MK-Bluetooth-USB should be set (Infolink).
Now the connection between the Kopter and the KopterTool should be established automatically. Should that not be the case you should close the KopterTool and start it again.

Features / Password

If you want to use an additional program like i.e. "Dubwise" on your cellphone you can connect also the MK-Bluetooth at the Kopter with your cellphone.
You need to have a password for that connection. The password for the Bluetooth-Modules is set by default to four zeros (0000).

MikroKopter: en/BluetoothSet (zuletzt geändert am 19.09.2013 16:10 durch LotharF)